Login:
Votes - 2, Average rating: 5 ( )

User manual Black & Decker, model 7054

Manafacture: Black & Decker
File size: 3.15 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


If your Drill has a reversing switch, open the chuck and remove screw in bottom of chuck (left hand thread). Insert the key in the chuck and tap it sharply in the direction the tool normally rotates — see at right. This will loosen the chuck shank threads and the chuck may be unscrewed by hand. SWITCHES To lock trigger in “ON" position when using accessories, depress trigger and push up locking button “B," Figure 4, then gently release trigger. To release locking mechanism, depress trigger fully, then release it. VARIABLE SPEED SWITCH (a) For normal operation, rotate the Variable Speed Locking Button “A,” Figure 4, clockwise until it stops. This permits “FREE HAND” speed control — the farther the trigger is depressed, the higher the R.P.M. (b) To set the trigger switch to produce a selected speed each time it is squeezed, first rotate the button clockwise until it stops. Fully depress trigger, and with the Drill running at highest R.P.M. push up switch locking button. Release trigger and the tool will stay “ON.” Now, rotate the button counterclockwise and you will notice a decrease in R.P.M. Continue rotating button until desired speed is obtained. To turn Drill “OFF,” squeeze trigger and release, (c) Use lower speeds for STARTING HOLES WITHOUT A CENTER PUNCH, DRILLING IN METAL OR PLASTICS, DRIVING SCREWS, DRILLING CERAMICS. Higher speeds are better for DRILLING WOOD AND COMPOSITION BOARDS, AND FOR USING ABRASIVE AND POLISHING ACCESSORIES. Do not lock the switch “ON” when drilling by hand so that you can instantly release the trigger switch if the bit binds in the hole. Be sure to release the switch locking button before disconnecting the plug from the power supply. Failure to do so will cause the tool to start immediately the next time it is plugged in. Damage or injury could result. REVERSING SWITCH (Nos. 7054, 7154 Drills only) For removing screws or easing drill bits out of tight holes, slide the Reversing Switch, Figure 5, toward “R” to reverse the drill motor. The trigger switch should be released to the “OFF” position before moving the reversing switch. After any reversing operations, return switch to the forward, “F” position. ACCESSORIES Recommended accessories for use with your Drill are listed below and in Black & Decker Home Products catalogs (CAUTION: The use of any other accessory or attachment might be hazardous). For safety in use, the following accessories should be used only in the sizes specified below: BITS, METAL DRILLING - Up to V4" with Va" DRILL, up to %" with DRILL. BITS, MASONRY DRILLING - Up to y2"- BITS WOOD DRILLING - Up to Vz" with Va" DRILL; up to 3/4" with %" DRILL HOLE SAWS - Up to IMs" with Va" DRILL; up to 1W' with %" DRILL. WIRE BRUSHES - Up to 3" diam. GRINDING WHEELS - Up to 2" diam. BUFFING WHEELS - Up to 4" diameter, BACKING PADS-4%// diameter. SANDING DISCS & POLISHING BONNETS up to 5" diameter. We strongly recommend that your first purchase be the No. U-2106 Safety Glasses which should be worn when using all drill accessories. Use only mild soap and a damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage the plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. Self lubricating bearings are used in the tool and periodic relubrication is not required. However, it is recommended that, once a year, you take or send the tool to a B&D Service Center for cleaning, inspection, and lubrication of gear case. To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment, (including brush inspection and repl...

Other models in this manual:
Power Screwdrivers and Drills - 7024 (3.15 mb)
Power Screwdrivers and Drills - 7124 (3.15 mb)
Power Screwdrivers and Drills - 7154 (3.15 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category