Votes - 1, Average rating: 5
(
)
)
|
Other manuals for this model:
Home Theater Systems - DAV-DS1000 (2.94 mb)
Home Theater Systems - DAV-DS1000 (2.78 mb)
manual abstract
3, 20m . 2) •Tuner cord (MINI DIN 8 pin, 2m . 1) • FM wire aerial (1) •Wireless data output cords (for front speakers) (MINI DIN 6 pin, 5m . 2) • SCART (EURO AV) cords (3m . 2) • Mains leads (for rear speakers) (2) • Cushions (for center speaker) (4) • Operating Instructions (1) • Speakers connection and Installation (card) (1) Getting Started 17GB Using the Remote You can control the system using the supplied remote. The remote control of this system employs a solar panel for indoor use that can get enough battery from normal lighting in the room. To avoid excessive battery consumption, make sure that the remote is always placed in a brightly lit place facing up. This way, the battery will remain charged. When using the remote, point it at the remote sensor on the control unit. Notes • Do not leave the remote in an extremely hot or humid place. • Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction. • Do not expose the solar panel of the remote to direct sunlight as it may be damaged. • If the remote is placed with its rear side up, or left in a dark place for long periods, battery charging will not occur and further use will lead to battery discharge (the remote becomes unusable). • Placing objects on the remote may results in buttons being pressed for long periods and shortened battery life. • As the battery runs out, the operating range of the remote becomes shorter. z Should the battery become exhausted, charge it by placing the remote in a brightly lit room, more than 5 days. Charging time will vary depending on how bright the room is. z The battery is fully charged before shipment. So you can use the remote for 340 days (100 times use per day) without any solar charging. z When the remote does not function even after the solar battery is charged in the light of the room. Press the RESET button on the upper rear side of the remote using a pointed object such as the tip of a mechanical pencil as shown below. 18GB Step 1: Speaker System Hookup Getting Started 19GB Connecting the subwoofer Connect the system connector of the control unit to the SYSTEM CONNECTOR jack of the subwoofer. When you insert the plug of the SYSTEM CONNECTOR cord, press and hold both ends of the plug. FOOT LIGHT HIGH LOW OFF EURO AV OUTPUT (TO TV) EURO AV INPUT (FROM VIDEO) SYSTEM CONNECTOR TUNER INPUT WIRELESS REAR L R SPEAKER IMPEDANCE USE 4. FRONT L REAR L CENTERFRONT R REAR R FOOT LIGHT HIGH LOW OFF Subwoofer Control unit SYSTEM CONNECTOR cord continued Setting up the wireless speakers (Wireless setting) You do not need to connect the rear speakers to the system; audio signals are transmitted from the connected front speakers to the rear speakers. You cannot use any speakers other than those supplied with this system. Note When you use the speakers in the Wireless setting, make sure to set “CONNECT” to “WIRELESS” in “SPEAKER SETUP” (page 32). Terminals for connecting the speakers Connect the To the Using the Front speakers WIRELESS REAR L and R jacks Wireless data output cords SPEAKER FRONT L (white) and R (red) jacks Speaker cords Center speaker SPEAKER CENTER (green) jack Speaker cord Rear speakers Mains Mains leads Wireless data output cord Mains lead Connect the mains leads of the rear speakers to mains, after all connections are finished. Speaker cord The connector and the colour tube of the speaker cords are the same colour as the label of the jacks to be connected. Grey (+) (+) (–) Black Colour tube (–) Connect the supplied speaker system to the subwoofer using the supplied speaker cords by matching the colours of the jacks to those of the cords. Do not connect any speakers other than those supplied with this system. To obtain the best possible surround sound, specify the speaker parameters (distance, level, etc.) on page 29. 20GB Center speaker Getting Started EURO AV OUTPUT (TO TV) EURO AV INPUT (FROM VIDEO) SYSTEM CONNECTOR TUNER INPUT WIRELESS REAR L R SPEAKER IMPEDANCE USE 4. FRONT L REAR L CENTERFRONT R REAR R FOOT LIGHT HIGH LOW OFF WIRELESS REAR L R FRONT L CENTERFRONT R Rear speaker (L) Rear speaker (R) Subwoofer Front speaker (R) Front speaker (L) To mains To mains Wireless data output cord Wireless data output cord Speaker cord Mains lead Mains lead Speaker cord Speaker cord continued 21GB z You can turn on/off the power of the rear speakers using the switch on the lower side panel of each rear speaker. The indicator on each rear speaker changes as follows: subwoofer power on/data received (green); subwoofer power on/no data (blinks green); subwoofer power off (red). Switch To avoid short-circuiting the speakers Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch another speaker jack or the bare wire of another speaker cord. Examples of poor instllation of the speaker cords Stripped speaker cord is Str...