DS Series IMPORTANT INFORMATION Fill out the enclosed warranty card and mail to the Perlick Corporation to register the warranty. If the card is not returned, the warranty period will begin from the date the equipment is shipped from the factory. This manual has been prepared to assist you in the installation of your Direct Draw Dispenser and to acquaint you with its operation and maintenance. We dedicate considerable time to ensure that our products provide the highest level of customer satisfa

Adjust the Secondary Air/ CO2 regulator located on the beer pump panel to a minimum operating pressure of 10 psig. Smart Coupler Probe Valve Lever Positions ¦ Connect the coupler to a regulated water supply with pressure less than 30 psig. Note: Pump damage may occur with pressure higher than 30 psig. ¦ Open the water supply. Then open probe valve on Perlick Smart coupler to the 45° position. See figure 2. The beer pump will slowly pump up the beer line in the trunk housing to set psig. Note: If

Probable Cause: Solution: Beer Flow Control Handle is in CLEAN position. Slowly turn Beer Flow Control Handle to ON position. Problem: Beer does not flow after keg is tapped. Probable Cause: Solution: Smart Coupler has locked up. First, turn Beer Flow Control Handle to OFF position then turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON position. Probable Cause: Solution: Beer Flow Control Handle is OFF. Turn Beer Flow Control Handle to CL

Slowly turn Beer Flow Control Handle to ON position. Problem: Beer does not flow after keg is tapped. Probable Cause: Solution: Smart Coupler has locked up. First, turn Beer Flow Control Handle to OFF position then turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON position. Probable Cause: Solution: Beer Flow Control Handle is OFF. Turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON

Adjusting CO2 Gas Flow 1. Turn regulator adjusting screw counterclockwise until it turns freely. 2. Turn hand valve counterclockwise on CO2 cylinder to the fully open position. 3. Turn regulator adjusting screw clockwise until desired pressure is reached (approx. 12-15 lbs.). Tighten stop nut on adjusting screw. 4. Open shut-off valve on bottom of regulator. CO2 Leak Test Shut Off Valve (Black Lever in Closed Position) Cover for Adjusting Broach Regulator Fitting Fitting for Red Air Hose Dilute

We dedicate considerable time to ensure that our products provide the highest level of customer satisfaction. If service is required, call Perlick at 1-800-777-7267 or your dealer who can provide you with a list of qualified service agents. For your own protection, never return merchandise for credit without our approval. We thank you for selecting a Perlick product and assure you of our continuing interest in your satisfaction. IMPORTANT WARRANTY INFORMATION A Warranty card is enclosed that mus

12.05.03 INSTALLATION AND OPERATION INSTRUCTIONS CONCESSIONAIRE PORTABLE DISPENSERS Table of Contents PREPARING THE CABINET FOR USE Specifications.........................................................2 List of Included Parts.............................................3 Tools Required.......................................................3 Plumbing................................................................3 Electrical ................................................................3 Inst

Therefore, we reserve the right to change specifications without prior notice. Form No. Z2219 2 Rev. 4.15.06 Preparing the Cabinet – Flat Top Bottle Coolers Uncrating and Inspection Remove all crating material before operating. Carefully inspect cabinet for hidden damage. If damage is discovered, file your claim immediately with the transport company. Perlick is not responsible for damage in transit. Plumbing No plumbing connections are required. Condensate from the cooling coil automatically ev

Screw connector to stainless steel beverage line on faucet standard. Tighten with a wrench, but do not over tighten. 2. Make sure lever handle on keg coupler is in the UP (untapped) position. Place one brown leather washer into wing nut end of black beer line connector hose and thread onto top of keg coupler. Hand tighten. 3. Place clamp on one end of red air line. Push end over air valve located inside cabinet. Tighten clamp with screwdriver. Turn shut-off valve to OFF (horizontal) position. 4.

40000B Piston Party Pumps Sturdy and easy to use. Has palm-sized handle to pump more air with less effort. Red thermoplastic cylinder; all metal coupler. Convenient vent button to control foaming. Includes two foot vinyl hose with nylon faucet. Easy to disassemble for cleaning. Packed in individual display cartons, 25 per case. Ship Weight: 25 oz. each For Single Valve Kegs Part No. 40000B For Imported Kegs Part No. 40025B Bellows Party Pump Unique polyethylene bellows seals out grit. No