Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Please throw away after assembly is complete.) 2 Retainers (with Lock Nut) Seat Tube Support Housing 2 Legs Motor Housing 2 Seat Tubes Back Base Front Curved Base Note: Tighten or loosen screws with a Phillips screwdriver or the assembly tool. Do not over-tighten the screws. M5 x 2,9 cm Screw – 4 #4 x 3,18 cm Screw – 2 Shown Actual Size IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. 3 4 Infant Seat/Rocker Assembly This package contains small parts in its unassembled state. Adult assembly is required. CAUTION • Locate the hole in each side rail. • Position the front tube so that it is a shape. • Fit the front tube to the side rails, as shown. Hold the front tube in place and proceed to step 3. Side Rail Hole Front Tube 2 • While pressing the tab on each end of the cross brace, insert the cross brace into the side rails, as shown. Make sure you hear a “snap” on each side. 1 Cross Brace PRESS PRESS Side Rails • Insert a M5 x 2,9 cm screw through the outside of each side rail and into the ends of the front tube. IMPORTANT! Please follow the next assembly (step 4) carefully to completely secure the front tube to the side rails. Front Tube Side Rail Hole Side Rail Hole 3 • Fit a retainer with lock nut onto the end of a screw and to the inside of a side rail. Tighten the screw using the assembly tool. Turn the tool clockwise to tighten. Hint: A lock nut has been factory assembled to the retainer. During shipment, the lock nut may have fallen out of the retainer. If it has, please fit it into the hexagonal hole in the retainer so that the rounded side of the lock nut faces out. • Repeat this procedure to fasten the screw to the other end of the front tube and side rail using another retainer with lock nut. Retainer with Lock Nut 4 Infant Seat/Rocker Assembly Seat Back Tube Sockets PRESS • Insert the seat back tube into the socket in each side rail. • While pressing the tabs on the ends of the seat back tube, continue to insert the seat back tube into the sockets in each side rail until the tabs “snap” into place. Make sure you hear a “snap” on each side. • Pull the seat back tube up to be sure it is secure in the side rail sockets. 5 Kickstand 6 PRESS PRESS Lower Pocket Hardboard • Fit the upper pocket on the pad onto the seat back tube. • Turn the hardboard over and insert it into the slot in the front edge of the pad. Seat Back Tube Upper Pocket 7 • While pressing the tab on each end of the kickstand, insert the kickstand into the small tube inside each side rail. Hint:The kickstand is designed to fit into the siderails one way. If you cannot insert it into the small tubes (inside the side rails), turn it around and re-insert it into the small tubes. • Push the kickstand into the small tubes until the tabs “snap” into place. Make sure you hear a “snap” on each side. • Pull the kickstand to be sure it is secure in each side rail. 5 Infant Seat/Rocker Assembly Swing Frame Assembly • Fasten the pad buckles on the front edge of the pad and underneath the seat. Make sure you hear a “snap” on both sides. Pad Buckles • Fasten the pad buckles around each side rail. • Press the fasteners together in the seat back portion of the pad. Pad Buckles Side Rail PRESS SEAT BACK 8 9 Restraint Strap Slots 10 PRESS ButtonLeg Housing • Place a housing on a flat surface. • Insert the button end of a leg into the hole in the housing. • Push the leg in until it “snaps” into the housing. • Repeat this procedure to assemble the other leg to the other housing. • Pull the legs to be sure they are secure in the housings. If you can remove them, you have not assembled them correctly. Please re-read and repeat this assembly step. 1 • Pull the other leg back until it “snaps” into place in the housing. • Repeat this procedure to “snap” the leg in the other housing into place. Leg 2 • From behind the assembly, insert the restraint straps through the slots in the pad. • Press to fasten the restraint strap assembly to the pad. 6 Swing Frame Assembly CORRECT Front Curved Base Hubs Back Base HUBS FACE IN • Place the front curved base on a flat surface so that it curves away from you. INCORRECT • Place the back base on a flat surface, behind the front HUBS FACING OUT curved base. • Position the leg assemblies so that the hubs are facing each other. • Fit the ends of the legs over the ends of the front and back bases, as shown. Hint:You may need the help of another adult to help you balance the assembly. FRONT BASE CURVES INWARD FRONT BASE CURVES OUT4 • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above. • If the leg assemblies are assembled incorrectly to the bases, pull the legs from the bases. Please re-read and repeat assembly step 3. 7 8 Swing Frame Assembly Seat Tubes • In...