5 CD Changer Operation .................................................................................................................... 7 Installation ...................................................................................................................................... 13 In Case of Difficulty ........................................................................................................................ 14 Switching the address setting ...............................

REFER SERVICING IMP 0 R TAN T "DANGEROUS TO QUALIFIED SERVICE INSTRUCTIONS VOLTAGE" INSIDE PERSONNEL. ACCOMPANYING THE PRODUCT. TH E PRO DU CT. SEE MARKING ON BOTTOMI BACK OF pAODUCT WARNING:TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCTTO RAIN OR MOISTURE. . FCCInformation . Thisdevicecomplies with Part15ofthe FCCRules. : Operation is subject to the following two . conditions: (1)Thisdevicemaynotcauseharmful . interference, and (2)this device must accept any . interferen

• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain se

To maximize your listening satisfaction, take a few minutes to carefully review all sections of this guide. Note: The following instructions also include the functions of the optional dealer-installed trunk-mounted compact disc changer. Not available in station wagon models. 1432.doc 1 RADIO FUNCTIONS BASIC CONTROLS DISPLAY PANEL TUNING 1 Power Button 1 Indicator for Tone Control 1 Wave Band and Station Recall Buttons 2 Volume Bar 2 Stereo Indicator 2 Function Control Button 3 Bass Control/Balan

All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating the Tester Using the Rotary Switch, add the following: WWarning Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decrea

This manual is distributed as an electronic manual on the following CD-ROM: CD Title: 1652C/1653B/1654B CD Rev. & Date: 9/2010 CD PN: 3798444 © 2010 Fluke Corporation. All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating th

The protective cap decreases the exposed probe metal to <4mm. This decreases the possibility of arc flash from short circuits. On page 45, under General Specifications, add the following to the Safety section: Complies with EN/IEC 61010-031:2002+A1:2008. 12/10 1

Tune to a desired radio program as described in the "RADIO OPERATION" section. 2. Insert a blank cassette tape into the CASSETTE COMPARTMENT. 3. Press the PAUSE button. 4. Press the RECORD button. The PLAY button is engaged simultaneously to start recording. With the built-in Automatic Level Control (ALC), the best recording quality is automatically adjusted. Changing the volume level will not affect the recording. califone.com 8 califone.com 9 5. To activate recording, release the PAUSE button.

TO BE OPERATING NORMALLY OR EXHIBITS A MARKED POWER SOURCES - CONNECT THE APPLIANCE ONLY TO A CHANGE IN PERFORMANCE (E) THE APPLIANCE HAS BEEN POWER SUPPLY TYPE DESCRIBED IN THE OPERATING DROPPED OR THE ENCLOSURE DAMAGED. INSTRUCTIONS OR MARKED ON THE APPLIANCE. SERVICING - THE USER SHOULD NOT ATTEMPT TO GROUNDING OR POLARIZATION - PRECAUTIONS SHOULD BE SERVICE THE APPLIANCE BEYOND THAT DESCRIBED IN TAKEN SO THAT THE GROUNDING OR POLARIZATION MEANS OF THE OPERATING INSTRUCTIONS. ALL OTHER SERVIC

To program a song sequence: 1. Press STOP first if the CD is playing. 2. Press the PROGRAM button. The CD display will show P:01 3. Press the (SKIP>>) and or (SKIP<<) buttons to select the first track to program. 4. Once the desired track is reached, press the PROGRAM button to enter the track number into memory. 5. Repeat steps 3 & 4 to program additional tracks. 6. Press the PLAY/PAUSE button to start programmed playback. Note: The program will be erased when you press the CD PROGRAM button. R