Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Caution : This symbol indicates explanations about dangerous matters. If users ignore this symbol and handle the device the wrong way, damage to home or property could result. Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device. Always make sure that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended to make a copy immediately and use the copy instead. When a cracked disc is used continuously, the size of the crack is likely to grow and this will eventually result in irreparable damage to the disc. Important to read and understand at all times. Safety PrecautionsSafety Precautions InstallationInstallation Place the drive on a level surface. -Failure to do so may cause the device to fall onto a hard surface, resulting in damage or malfunction. Do not place the drive in direct sunlight. Avoid low-or high-temperature environments. Avoid high-humidity environments. Safety Precautions While Operating Handle with caution to prevent damage from external shock. Do not drop the drive, and protect it fromsevere shocks. -It can damage the drive or cause it to malfunction. Do not move the drive while in operation and do not attempt to open the disc tray byforce. Make sure to close all working programs before attempting to open the tray and always usethe open/close button. -Do not insert a pin into the emergency opening while in operation. Do not use cracked, distorted or damaged discs. -In particular, a disc with a crack on the inner tracks may break while in use. Safety Precautions Other Never allow food particles or foreign substances to enter the drive casing. To protect against the risk of fire, do ot spill such liquids as alcohol and benzene on the drive. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. -To reduce the risk of damage, electric shock, and fire, Introduction Front 1. Headphone Connector The sound output terminal enables you to plug stereo headphones into the drive. It requires a 3.6 mm stereo mini-jack. 2. Headphone volume control This headphone volume control adjusts the volume for your headphones. You can only use the headphone jack and volume control when you have installed the required software utilities. For example, the Microsoft Windows Media player can be used. 3. Disc compartment The compartment opens and closes automatically when you press the Eject button. 4. Emergency eject hole If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) 5. LED 6. Eject Button Design and specifications are subject to change without prior notice. IntroductionIntroduction Rear 1. Digital output terminal You can connect a sound card or MPEG card which support Digital output terminal to your drive using this two-pin terminal. 2. Sound output terminal You can connect a sound card to your drive using this four-pin terminal. This function is not covered in detail in this guide. Refer to the documentation supplied with your sound card. 3. Master/slave select terminal Usually, this is a pre-set configuration as illustrated below. Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct position. 4. Interface terminal This input/output interface terminal is used to connect the 40-pin flat cable from the IDE interface to the CD-ROM drive. 5. Power terminal The power terminal is a four-conductor male plug. (A : +5V DC) (B : +12V DC) SetupSetup Installing the CD-ROM Drive To install your CD-ROM Drive in the PC, proceed as follows. Make sure that the PC is powered off and disconnected from any power source. If necessary, attach a horizontal bracket to both sides of the drive. Remove the cover from a free expansion slot and install the CD-ROM drive, as shown in the illustration. Connecting the Cables Setup Connecting the power cable The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the CD-ROM drive. A - Cut Side 1 +5V DC 2 Ground 3 Ground 4 +12V DC Note: An improperly connected power cable may cause trouble. Check the direction of the power connector and the incline side of the CD-ROM drive before connecting. Connecting the IDE cable Insert the IDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) When using one IDE cable Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the CD-ROM drive. a : Slave Drive (Choose the SL Jumper) b : Hard Drive c : MainBoard When using two IDE cable If there ...