8-211505 HOUSING (R) 1 44 MC-6154-211504 CONNECTOR 1 10 MC-9040-310175 BAR 1 45 MC-6017-211503 FRONT-HAND GUARD 12 MC-6228-211506 OIL PIPE ASS'Y 1 46 MC-6228-211303 FIXED ACC'Y 1 13 MC-6076-210503 WASHER 1 48 MC-6SDABB04-16 SCREW 14 MC-6056-211502 SWITCH BUTTON 1 49 MC-6079-211503 SPRING 1 15 MC-6066-211501 OIL TENK 1 50 MC-6038-211506 HOUSING (L) 16 MC-6028-211502 TRIGGER 1 51 MC-6086-211501 REAL COVER 1 17 MC-6022-211502 SWITCH 1 52 MC-6228-211301 MOTOR GEAR BOX ASS'Y

BA_ SE_135_ 003_01_02.fm0457 184 3021. M2. L6. CP. Printed in USA Printing inks contain vegetable oils; paper can be recycled. Contents Safety Precautions and Working Techniques ......................... 2 Maintenance Chart ......................... 26 Main Parts of the Saw .................... 28 This manual contains the safety precautions and recommended cutting techniques outlined in STIHL instruction manuals for gasoline-powered chainsaws. Even if you are an experienced chainsaw user, it is

Re-install cover knobs and tighten securely. 10. Tighten the tension bolt until the indicator reaches the white line. Refer to chainsaw owner’s manual for the proper oil/gasoline ratio. Maintain an ample supply of bar and chain oil in the reservoir to lubricate the drive mechanism of the RIPSAW. 3 Dimension plate assembly Figure 1. Dimension plate assembly 1. Remove dimension plate and parts from box. 2. Slide guide arm under handle bracket with square pin facing downward. 3. Install and tighten

1 Assembly Chainsaw assembly and preparation ..............................… 2 Compatible chainsaws and sprockets ……………………… 2 RIPSAW assembly ….........................................................…. 3 Dimension plate assembly …........................................…. 4 Guide beam assembly.......................................….……… 5 End clamp assembly …………………………………………….. 6 Blades Changing blades …..............................................……….. 11 Tracking blades Drive wheel …………………………

-20 X 2 STUD RS999 13 TRACKING WASHER RS999 14 . - 20 NUT RS999 15 . -20 ALLEN BOLT (TRACKING) RSH00 11 DRIVE COUPLING RSH00 12 DRIVE DISK - ELECTRIC RSH00 13 ADAPTER BLOCK RSH00 15 PINION COVER RSH00 70 PINION SPACER RSH50 44 RING GEAR RSH50 55 PINION GEAR RSH70 38 038 SPROCKET RSH70 39 064 SPROCKET RSH70 47 036 SPROCKET RSH70 48 044 SPROCKET RSH70 49 20" BAR - STIHL RSH70 50 CHAIN FOR 20" BAR RSH70 51 STIHL WASHER RSH70 52 2.6 STIHL ENGINE OIL RSH70 53 STIHL BAR NUT RSH70 54 STIHL SNAP RING RS

Make sure chainsaw switch is in the off position. Shut off gas powered chainsaw before attempting to sharpen the blade. 3) Move the dimension plate to at least a three-inch depth. 4) Lay the RIPSAW on its side with the front side facing upward. 5) Insert diamond stone into gullet of each tooth. While applying slight pressure upward so thtat , move the stone in and out (Forward and backward) in short strokes under the cutting tip of the blade. 6) Keep the stone perpendicular or square to the blad

Ignited Vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. NOTE: Dispose of the old fuel/oil mix in accordance to Federal, State and Local regulations. Remove fuel capWARNING: slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place. Add fuel in a clean, WARNING: well ventilated outdoor area. Wipe up any spilled fuel

B . for cracks in the links and damaged rivets - replace any damaged or worn parts of the chain and match the new parts to the shape and size of the original parts. . It is absolutely imperative to comply with the angles and dimensions specified below. If the . . - and in particular if the depth gauge is set too low - there is a risk of increased kickback of the chainsaw, with resulting . . . See “Technical Data” for the permitted chain pitches. The chain pitch (e.g. 3/8) is

If the engine doesn’t start: Tank has been run until completely dry : Pull the starter grip slowly with your When the engine begins to fire: right hand until you feel it engage – and then give it a brisk strong pull. : Turn choke knob clockwise, away and then refueled: : Press fuel pump bulb at least 5 times – even if bulb is filled with Do not pull out the starter rope all from g. the way – it might otherwise break. : Press decompression valve button Do not let the starter grip snap back again