Votes - 2, Average rating: 3.5 ( )

Manafacture: Stihl File size: 766.45 kb File name: Language of manual:

-20 X 2 STUD RS999 13 TRACKING WASHER RS999 14 . - 20 NUT RS999 15 . -20 ALLEN BOLT (TRACKING) RSH00 11 DRIVE COUPLING RSH00 12 DRIVE DISK - ELECTRIC RSH00 13 ADAPTER BLOCK RSH00 15 PINION COVER RSH00 70 PINION SPACER RSH50 44 RING GEAR RSH50 55 PINION GEAR RSH70 38 038 SPROCKET RSH70 39 064 SPROCKET RSH70 47 036 SPROCKET RSH70 48 044 SPROCKET RSH70 49 20" BAR - STIHL RSH70 50 CHAIN FOR 20" BAR RSH70 51 STIHL WASHER RSH70 52 2.6 STIHL ENGINE OIL RSH70 53 STIHL BAR NUT RSH70 54 STIHL SNAP RING RSH90 55 PINION ASSEMBLY ST800 99 STIHL-20" BAR & CHAIN 9 10 Text Box: RS000 22 RS500 72 Text Box: FRONT VIEW Text Box: REAR VIEW Text Box: RS100 22 – BLADE GUIDE BLOCK ASSEMBLY Text Box: RS H00 11 RS 500 70 RS H50 55 Text Box: RS H00 70 Text Box: TOP VIEW SIDE VIEW Text Box: RS H90 55 – PINION ASSEMBLY Text Box: RS 000 01 Text Box: RS 000 02 Text Box: RS 000 68 RS000 06 RS000 08 RS100 56 RS500 71 Text Box: RSH59 44 Text Box: RS001 01 Text Box: RS001 02 Text Box: RS500 70 Text Box: RS000 14 Text Box: RSH00 13 Text Box: RS000 31 Text Box: FRONT SIDE VIEW Text Box: RS000 04 Text Box: RS000 09 Text Box: RS000 11 (6) Text Box: RS000 29 RS000 12 RS000 30 Text Box: RS000 10 Text Box: RS000 27 Text Box: RS999 10 (SEE DIAGRAM BELOW) Text Box: RS000 28 Text Box: RS000 36 Text Box: RS999 11 Text Box: RS999 15 Text Box: RS999 13 Text Box: RS999 12 Text Box: RS999 14 Text Box: RS000 52 IDLER TRACKING ASSEMBLY Text Box: REAR IDLER PLATE Text Box: FRONT VIEW Text Box: TOP VIEW Text Box: TENSION Changing blades Wear gloves and eye protection while handling blades. 1. Release blade tension. (Turn tension bolt counter-clockwise.) 2. Remove cover knobs. 3. Remove front tension arm, Drive cover and Idler cover. 4. Slide blade toward front of saw and out of guide blocks. 5. Slip blade over the edges of the bottom of the Drive and Idler wheels by tipping it up and outward. 6. Rotate blade up and out of safety guard. 7. To replace blade perform above procedures in reverse. Make sure that locating pins are through the holes in the front covers before installing and tightening cover knobs. 8. Tighten the tension bolt until the tension indicator reaches the white line on the rear tension arm. Carbide guide replacement/adjustment Carbide guides may need to be adjusted occasionally. If your sawmill is making wavy cuts adjusting the carbide guides may solve the problem. If using blades of thicknesses other than .025” you will need to adjust the carbide guides. 11 Text Box: 1. Install blade if necessary 2. Loosen screws 3. Place a piece of paper between blade and top carbide 4. Using vise grips or pliers, squeeze the carbides tother 5. Tighten screws while holding carbides in place Text Box: 1 2 3 4 Blade trackin g Drive wheel… The tracking set screw is located on the front drive cover at the wheel hub. Turning the set screw will move the wheel, which in turn will move the blade forward and backward. The smooth side of the blade should track approximately 1/32” from the rear rim of the Drive wheel. a) Install a new blade if necessary. b) Loosen tracking lock screw. c) Adjust the Drive wheel tracking screw all the way in. d) Tighten the blade so that the indictor reaches the white line. e) Rotate the blade by hand to make sure that it will not come off the wheel when the saw is jogged (Jogging the saw consists of starting the motor and running the saw intermittantly). f) Jog the saw while turning the tracking screw counterclockwise, until the blade leaves the back flange of the Drive wheel. g) Continue jogging the saw while adjusting the Idler wheel tracking bolt. h) Lock the Idler tracking bolt by tightening the 1/4-20 nut. Idler wheel… The tracking adjustment for the idler wheel is located on he rear side of the sawmill. t 1. Loosen locking nut, using a 7/16” open-end wrench. 2. Make tracking adjustment using a .” wrench by turning tracking nut clockwise to move blade backwards (towards you) and turning nut counter-clockwise to move blade forward. (Away from you) You will need to follow the tracking nut with the lock nut to achieve the proper results. 3. Tighten locking nut. The smooth side of the blade should track evenly with the rear edge of the Idler wheel. BLADE REAR (teeth) BLADE FLANGE (teeth) RIMLESS EDGE 12 Text Box: 1/32 Text Box: REAR TENSION ARM Text Box: LOCKING NUT (located between Rear Idler Plate and Tracking Bracket) Text Box: TENSION INDICATOR Text Box: IDLER TRACKING BRACKET Text Box: IDLER WHEEL Text Box: DRIVE WHEEL SShhaarrppeenniinngg bbllaaddeess WW 1) You will first need to remove the steel guide from the Oregon sharpener for sharpening Ripsaw saw blades. 2) It is recommended that you sharpen the blade while it is on the RIPSAW. Unplug electric chainsaw from power source. Make sure chainsaw switch is in the off position. Shut off gas powered chainsaw before attempting to sharpen the blade. 3) Move the dimension plate to at least a three-inch depth. 4) Lay the RIPSAW on its side with the front side facing upward. 5) Insert...

Download now

Please, enter two numbers from picture: