Votes - 2, Average rating: 4 ( )

Manafacture: Poulan File size: 673.76 kb File name: 67f77b5d-178c-2764-8591-89423041e1d4.pdf Language of manual:

6 The chain is sharp and can cut you even when it is not moving! S Loosen and remove the chain brake nuts and the chain brake from the saw. S Remove the plastic shipping spacer (if present). Location of shipping spacer ChainBrakeChainBrakeNutsBarTool SAnadjustingpinandscrewisusedtoadjustthetensionofthechain.Itisveryimportantwhenassemblingthebar,thatthepinlocatedontheadjustingscrewalignsintoaholeinthebar.Turningthescrewwillmovethead- justmentpinupanddownthescrew.Locatethisadjustmentbeforeyoubeginmountingthebarontothesaw.Seeillustrationbelow. Inside view of Chain Brake Adjustment located on Chain Brake S Turn the adjusting screw by hand counterclockwise until the adjusting pin just touches the stop. This should allow the pin to be near the correct position. S Slide guide bar behind clutch drum until guide bar stops against clutch drum sprocket. MounttheBar S Carefully remove the chain from the package. Hold chain with the drive links as shown. CUTTERSMUSTFACEINTipofBar DIIRECTION OF ROTATION Cutters Depth Gauge Drive Links Place chain onto the sprocket S Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. S Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. S Fit chain drive links into bar groove. S Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove. NOTE: CHAIN BRAKE MUST BE DISENGAGED BEFORE INSTALLATION ON THE SAW. TO DISENGAGE CHAIN BRAKE, PULL THE FRONT HAND GUARD BACK TOWARD THE REAR OF THE CHAIN BRAKE AS FAR AS POSSIBLE (SEE ILLUSTRATION). ENGAGEDAGEDGDISENChainBrakeFrontHandGuard S Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned. S Install chain brake nuts and finger tighten only. Once the chain is tensioned, you will need to tighten chain brake nuts. CHAIN TENSION (Including units with chain already installed) NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage. Checking the tension: Use the screwdriver end of the chain adjustment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar. ChainBrakeNutsChainAdjustmentTool(BarTool) Adjusting the tension: Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw. You can adjust the chain tension by loosening the chain brake nuts and turning the adjusting screw 1/4 of a turn while lifting up on the bar. S If chain is too tight, turn adjusting screw 1/4 turn counterclockwise. S If chain is too loose, turn adjusting screw 1/4 turn clockwise. ChainBrakeNutsGuideBarAdjustingScrew--1/4Turn AdjustingScrew S Lift up the tip of the bar and tighten the chain brake nuts with the bar tool. S Recheck chain tension. ChainBrakeNuts WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury. 7 OPERATION KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. ChainAdjustmentTool(BarTool) PrimerBulbStarterChainFrontHandGuardFrontHandleStarterRopeON/STOPSwitchMuffler Bar Oil Fill Cap Housing Fuel Mix Fill Cap GuideBarChainBrakeNutsCylinderCoverThrottleLockoutRearHandleThrottleTriggerChokeKnobChainBrakeChainDirectionofTravelAdjustingScrewChainCatcherFastIdleLockBarSprocketHole ON/STOP SWITCH The ON/STOP SWITCH is used to stop the engine. THROTTLE TRIGGER The THROTTLE TRIGGER controls engine speed. THROTTLE LOCK- --OUT The THROTTLE LOCK- --OUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from accidentally squeezing the trigger. FAST IDLE LOCK The FAST IDLE LOCK holds the throttle trigger in the starting position. Activate the fast idle lock by pressing the throttle lockout and squeezing the throttle trigger. With the throttle trigger squeezed, press the fast idle lock. Release the throttle lockout and trigger while holding the fast idle lock button. CHOKE KNOB The CHOKE KNOB activates the choke to provide additional fuel to the engine during cold starting. 8 PRIMER BULB The PRIMER BULB circulates fuel to the carburetor to provide quicker starting. CHAIN BRAKE The CHAIN BRAKE is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of kickback. The chain brake activates manually if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front handle as fa...

Download now

Please, enter two numbers from picture: