Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
A cold window glass surface will weaken the adhesive strength of the double-sided tape. Also, if installation inside the cabin is performed on a day with high humidity or when it is raining, the high humidity level will weaken the adhesive strength of the double-sided tape. • Do not install the antenna in a location where it may obstruct the field of view during driving, such as on the windshield. 1 Check the location where the antenna is to be attached.Clean off any grease or dirt from the installation location using the supplied glass cleaner (Accessory G), clean the area with water and allow to dry. Antenna parts Antenna unit 2 CAUTION Clean the glass thoroughly as failure to clean the glass can not only weaken the adhesive strength of the double-sided tape, but may also cause it to come loose. 2 Remove the protective strips from the antenna parts and the back of the antenna unit. 3 Attach the double-sided tape of the antenna parts and the antenna unit to the rear windshield glass. Attach the double-sided tape by firmly pressing down from the top. Secure cables using the supplied clampers. 4 After attaching the antenna with the double-sided tape, allow it to sit undisturbed for 24 hours. Take care not to apply force to the antenna or allow it to get wet during this time. 5 Wire the antenna cable to the main unit. Bundle cables with the Rear window Rear seat clamper bar (Accessory H) 2 CAUTION Incar antennas have a lower reception sensitivity than antennas intended for outside mounting. The picture may not appear or may be disturbed if the signal in your area is weak. 5 – + To the main unit Ignition cable (Red) .12V Ignition key switch Car fuse box(Main fuse) ACC Ground cable (Black) · (To car chassis) Battery Fuse(1A) Connection – + AV IN VIDEO 2 IN AV OUT Battery wire (Yellow) .12V Ignition wire (Red) .12V Parking sensor wire (Green) Ground wire (Black) · (To car chassis) To parking brake detection switch harness of car For the sake of safety, be sure to connect the parking sensor. 2 CAUTION FM transmitter antenna (White) Center unit LX-BUS cable Back view camera,etc VCR,etc Fuse(5A) (Accessory A) (Accessory F) Ignition key switch Car fuse box(Main fuse) ACC Battery •Visual (Yellow) •Audio left (White) •Audio right (Red) •A center unit and KCA-S210A are necessary to connect a changer unit. Refer to the instruction manual of KCA- S210A for the connection method. Connect this unit to terminal “TO CHANGER 2”. • To connect this unit to KCA- NOTE Do not connect an LX-BUS cable. 2 WARNING Other Monitor or Aux input of the audio unit FM-TX S210A, extended cable CA-2 CAUTION C2EX or CA-C5EX is Do not leave this unit in any position where the FM transmitter necessary. antenna is bent or blocked off by metal parts. • This unit cannot be connected to any system where two KCA S210As are connected. • If this unit and a DAB unit are connected to a center unit, do not use KCA-S210A, but connect this unit to the disc changer connection terminal of the DAB unit. Removing the Unit ¦ Removing the Hard Rubber Frame 1 Engage the catch pins on the removal tool and remove the two locks on the lower level.Lower the frame and pull it forward as shown in the figure. 2 When the lower level is removed, remove the upper two locations. NOTE The frame can be removed from the top side in the same manner. ¦ Removing the Unit 1 Refer to the section “Removing the Hard Rubber Frame” and then remove the hard rubber frame. 2 Remove the screw (M4 . 8 ) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. CatchLock Accessory E Catch facing up 2 CAUTION Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. ...
Other models in this manual:Car Video - VZ-7000N (312.21 kb)