Votes - 3, Average rating: 4 ( )

Manafacture: Craftsman File size: 1.49 mb File name: Language of manual:

Top installation 2_Strand Bell Wire Wall Control Bottom Terminals Installation Ftange Opener Terminal Screws Back Panel Antenna of Opener WIRING INSTRUCTIONS FOR ACCESSORIES Open Door Indicator:. TOwhite & orange opener terminals Outdoor Key Switch: To red & white opener terminals Touch Code Lock: TO red and white opener terminals Infrared Reversing System: To while & black opener terminals !3 r_ Installation STE P7 Install Light and Lens PROCEDURE: Install a light bulb, (75 Watts Max-Guide imum) in socket as shown The light will turn on and remain lit for 4-!/2 minutes when power is connected After 4-1/2 minutes it will turn off If light bulb burns out prematurely due to vibration, replace with a "rough service" bulb. Len INSTALLING LENS: Slide lens into the lens guides as shown Snap bottom tabs into lens slots Lighl Lens _ab _ 75LightWattBulbMaX STE P 8 ConnectPower Electric TO AVOID SERIOUS PERSONAL INJURY FROM ENTANGLEMENT, REMOVE ALL ROPES CONNECTED TO THE GARAGE DOOR BEFORE OPERATING OPENER. TO AVOID DAMAGE TO GARAGE DOOR AND OPENER, MAKE DOOR LOCKS INOPERATIVE BEFORE CONNECTING ELECTRIC POWER. USE A WOOD SCREW OR NAIL TO HOLD THE LOCKS IN "OPEN" (UNLOCKED) POSITION° INSTALLATION AND WIRING MUST BE IN COMPLIANCE WITH LOCAL ELECTRICAL AND BUILDING CODES. OPERATION AT OTHER THAN 120V 60Hz WILL CAUSE OPENER MALFUNCTION AND DAMAGE. Opener MUST be permanently wired or plugged into a grounded 3-prong receptacle wired according to local electrical codes DO NOT use a 2-wire adapter DO NOT use an extension cord PERMANENT WIRING CONNECTION Ground Tab iround Screw RIGHT WRONG Ground Wire IF LOCAL CODES REQUIRE PERMANENT WIRING: DISCONNECT POWER AT FUSE BOX BEFOREPROCEEDING. PROCEDURE: Refer to illustration Make connection through the 7/8 inch diameter hole in top of opener chassis Wife 1 Remove opener chassis cover by removing the cover screws 2 Remove attached 3-prong cord CAUTION: BE SURE THAT UNIT IS GROUNDED 3 Connect the black (line) wire to the black wire on ACCORDING TO LOCAL CODE, terminal block; white (neutral) wire to the white terminal wire; the green (ground) wire to green IMPORTANT NOTE: TO AVOID INSTALLATION ground screw DIFFICULTIES, DO NOT RUN OPENER NOW. 14 Installation STE P9 Install Door Bracket and Plate Follow instructions which apply to your door type as illustrated below TO PREVENT DAMAGE TO LIGHTWEIGHT GARAGE DOORS, ALWAYS REIN FORCETHE INSIDE OF DOOR--BOTH VERTICALLY AND HORIZONTALLY--WITH 2x4 BOARDS OR ANGLE IRON. Horizontal brace should be at least 6 feet long Vertical brace should cover height of top panel The best solution is to check with your garage door manufacturer for a door reinforcement kit for an opener installation. Sectional Door Installation Procedure 1 Assemble the door bracket and plate as shown. Center bracket on previously marked vertical SECTIONAL DOOR guideline Header 2 Position bracket assembly on face of door within gracket the following limits: A. Top edge of bracket 2" to 4" below the top edge of door B. Directly below any structural support across top of door Vertical _ Waii Header Placement depends on your particular needs Center_._ _ Line _ I 3 Mark and drill 5/1 6" TOP and BOTTOM fasten- I I ing holes Secure bracket as shown I Door Brackel & Door I Plate Assy Carriage Boll. "" =_ _=Y 6/16 ,.18x2.!/2-_ Bracket --_. Door Bracket ... Washer Lock 5/16" Door Arm Board for Inside Edge Lightweight Doors of Door orBoard _. 5/16"-!8 Reinforcement AiD One-Piece Door Installation Procedure NOTE: The door bracket has left and right side NOTE: Door bracket may be installed on face of fastening holes, Assemble and install the door door if required for your installation. (Refer to bracket and plate if your installation requires top dotted line drawing,) HOWEVER, drill3/1 6" pilot and bottom fastening holes. holes and substituteS/1 6"xl -1/2" lag screws(not 1 Center bracket (with or without plate as required) supplied) to fasten the bracket to door, on top edge of door as shown Mark holes 2_ Drill two 5/1 6" holes and fasten door bracket ONE PIECE DOOR with hardware supplied Header Bracket NOTE: If the door has no exposed framing. drill 3/16" pilot holes and use 5/16"x1-1/2" lag screws (not supplied) to fasten bracket to t top of door. Header Door Wall Nut I Door Bracket Plate Door Arm Door Bracket Door 5/16" Face of Door Bracket Plate Installation (Optional) Vertical Top Edge Center of Door Optional) Line (Outside) I Carriage Bolt i (_/ 6/16'-18x2-1/2" 15 installation STE P 10 Connect Door Arm to Trolley Follow only those instructions SECTIONAL DOOR FIG, A. Make sure garage door is closed tight, Connect straight door arm section to trolley with a clevis pin. Secure with a ring or cotter pin fastener(if cotter pin is used, spread to secure) Fasten curved section to door bracket in the same way FIG,, B. Bring arm sections together Find two pairs of holes that line qp and join sections Insert screws from straight arm side Select holes as far apart as possible to increase door ...

Download now

Please, enter two numbers from picture: