Login:
Votes - 3, Average rating: 3.7 ( )

User manual Allstar Products Group, model 8822

Manafacture: Allstar Products Group
File size: 169.36 kb
File name: 817905d2-a190-4b8b-9d0a-dfd227fa0d60.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Receiver, first set your receiver coding switches to your private code setting using the instructions that follow THEN program your Allstar Classic Quik Code transmitter (following the instructions included with the transmitter) to match the receiver. Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. MODEL 9921 AND 8822: The coding switch in these models consists of eight or nine small switches each of which can be placed in two different positions, On or Off. See Fig. 3. Using a small screwdriver, set the coding switches in both the transmitter and receiver identically. (Your private code). FIGURE 3 DO NOT SET ALL SWITCHEs IN THE SAME POSITION. EXAMPLE: NOT ALL RELAY RADIO 3 2 1 24 VOLTS POWER COMMON FIGURE 4 C. Models 9921 or 9931 Single Door Garage 3 2 1 ON or OFF STEP 2: INSTALL YOUR RECEIVER A. The receiver was designed to be installed in a variety of ways depending on the type of operator and the application. If standard hook- up is not desirable or possible, accessories such as three wire adapter sets and transformer adapter kits must be used. B. Standard hook- up to three terminal operators: For direct connection loosen the three screws on the operator and slide the brass terminals under these screws. See Fig. 4. Replace the pushbutton wiring and tighten the screws. Be certain the antenna wire is hanging down vertically and the receiver terminal numbers printed on the receiver case match the numbers on the operator terminal strip. (1) D. Model 8832 - Double Door Garage 3 2 1 3 2 1 3 2 1 3 2 1 (2) (1) E. Model 8833 - Three Door Garage (1) (3) (2) 3 2 1 3 2 1 3 2 1 FIGURE 5 104388 B. If the operating distance drastically decreases, remove the battery access door See Fig. 1A, and replace the battery with a NEDA 1604, nine volt battery. C. Models 9921 and 9931: To activate your garage Door or Gate, simply depress your transmitter button until the door or gate starts to move. D. Models 8822, 8832 and 8833: To activate the desired Garage Door or Gate control, push either bu...

Other models in this manual:
Safety Gate - 9921 (169.36 kb)
Safety Gate - 9931 (169.36 kb)
Safety Gate - 8832 (169.36 kb)
Safety Gate - 8833 (169.36 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category