Votes - 2, Average rating: 5
(
)
)
|
manual abstract
Improper installation could result in the gate becoming dislodged from the doorway, or unstable. Always make sure the extension is securely attached to the gate beforeusing. The safety of your child is your responsibility. Note:Ifusing this gate at the top of stairs,the 4 Wall Cups MUST beused.Ifnot used, the gate could be dislodged from the opening. It is preferable to install the extension on the hinge side of the gate. If you have an application that requires additional extensions, please contact tlieretailer which you purchased your gate from. We offer, the following sizes of extensions for your gate: 4 inch, 6 inch, 12 inch and 24 inch. They are available at mostretailers that carry our Regalo Products line of metal gates. For questions regarding your gate, or replacem ent parts contact our customer care depailment at 952-440-1950. You in ay also write us at: Regalo International Inc., 14198 CommerceAve. N.E. Suite 600, Prior Lake, MN 55372. Madein China. Instructions for Gate Extension 1. Assemble the gate per the gate instructions. 2. Choose the side of the gate to be extended and remove the top and bottom Adjustment Wheel Spindles. 3. Assemble the gate and extension as illustrated 4. Reposition the gate and fit in accordance with the gate fitting instructions. Important: Keep these instructions for future reference Regalo Widespan Gate Model# 1158 Assembly and Installation Instructions Please read these instruction.? carefully before inst alling your gate. The safety of your child is your responsibility. This gate can be used in openings from 29 inches to 58 inches. Contact Regalo for questions and replacement parts. If in doubt the use of your gate, call our customer care line at 952-440-1950 Regalo International Inc., 14198 CominerceAve. N.E. Suite 600, Prior Lake, MN 55372. Made in China. Check that you have these contents: 1. Gate Frame JPPrl A WARNING: / Intended for young children aged six months through 24 months. Check the gate regularly to see if all the hardware and mountings are tightened. To prevent serious injury or death,securely install gate or enclosure and use according to m anufacturer’s instructions. Never use with a child adle to climb over or dislodgetlie gate or enclosure. Never leave child unattended. 1--Use only with the locking/latching mechanism securely engaged. Note:If using this gateatthetop ofstairs,the4wall CupsMUST beused.Ifnot used, the gate could be dislodged from the opening. 2. Hardware Pack which should contain: 4 - Threaded Spindle Rods 4 - Adjustable Wheel Spindles q (already assembled to the Spindle Threaded Rods) 4-WallCups 0 4 - Screws s=»» 3. Three Extensions 12" Extension 6" Extension 4" Extension T ex I Œ I cx (1) Important: Keep these instructions for future reference J^eaaÎo Widespan Gate Model #1158 Assembling and Installing Your Gate **Note: IMPORTANT you will notice a slight Gap between the gate door latch and the frametube. THISIS NOT A DEFECT. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in the doorway. Step 1. Begin by locating the 4 Threaded Spindle Rods. Before you begin, turn the Adjustment Wheels clockwise until they are almost against the flat end of the Threaded Spindle Rods. WARNING: The Adjustment Wheel should NOT touch the flat end of the Thread Spindle Rod. If it does it might get stuck. Diagram A. r Step 2. You are going to insert the 4 Threaded Spindle Rods into the holes in the 4 ends of the gate frame as shown in Diagram Bl. * * IMPORTANT: THE ENDS OF THE GATE FRAME ARE NOT THREADED. THE THREADED SPINDLE ROD SHOULD SLIDE INTO THE END OF THE FR4ME TUBES WITHOUT ANY RESISTENCE. Push the Threaded Spindle Rods all the way into the frame tube until the Adjustment Wheel hits the end of the frame tube as shown in Diagram B2. Diagram B 1 Diagram B 2 Adjustment Wheel (2) Important: Keep these instructions for future reference K,eaaio Widespan Gate Model #1158 Step 3. Positioning and Attaching the Wall Cups to your door opening. Your gate is a pressure mounted gate. Therefore it is not necessary to use the screw attached Wall Clips to your door opening if you choose not to. However, IF YOU ARE USING THE GATE AT THE TOP O F STAIRS YOU MUST USE THE WALL CUPS. Regardless of whether you are using your gate at the top of stairs or not, using the Wall Cups will affix your gate more firmly in the doorway. So you may choose to use them in all applications. If you choose not to use the Wall Cupsyou may skip to Step 4 now. Before attaching your Wall Cups to your doorway opening you must make sure you have the screw holes marked correctly. It is important to install the gate with a spacing of not more than 3 ” from the floor To do this, simply position your gate in the doorway so that it is level and centered as shown in Diagram C-1. Then, place the Wall Cups over the fl at end of the Threaded Spindle Rods which should already be fully ...