When you are tuned to a station that is not transmitting traffic information, but another RDS station starts transmitting a traffic bulletin, the tuner automatically switches to the other station for the duration of the bulletin. Alarm When an emergency transmission (announcing disasters, etc.) functions are interrupted to be received. Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it. When using a new CD If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc. Burrs Burrs CD accessories Don’t use disc CD cleaning Clean from the center of the disc and move outward. Removing CDs When removing CDs from this unit pull them out horizontally. CDs that can’t be used • CDs that aren’t round can’t be used. • CDs with coloring on the recording surface or that are dirty can’t be used. • This unit can only play the CDs with . It may not correctly play discs which do not have the mark. • A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing and your CD-R/CD-RW recorder manual.) CD storage • Don’t place them in direct seat or dashboard temperature is • Store CDs in — 5— English English Power Release button VOL ADJ SCRL SCANAUD TI RDM REP M.RDM CLK MENUOFF PTY LOUD AM FM . 4u d CLK ATT/ Q/ SRC LOUD AUD LOUD indicator SYSTEM Q indicator ATT indicator Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUNER" CD "CD" External disc "DISC" (Function of the KDC-4027/KDC-4027V) Standby (Illumination only mode) "STANDBY" This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicles battery. The time until full power OFF can be set in (page 8) . First, select the speaker type with the Speaker setting. • When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. Loudness Compensating for low and high tones during low volume. Press the [LOUD] button for at least 1 second. Each time the button is pressed for at least 1 second the Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. System Q You can recall the best sound setting preset for different the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed Sound setting Display Flat "FLAT" Rock "ROCK" Top 40 "TOP40" Pops "POPS" Jazz "JAZZ" Audio Control 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. Adjustment Item Display Range Bass level "BAS" –8 — +8 Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BAL" Left 15 — Right 15 Fader "FAD" Rear 15 — Front 15 5 Exit Audio Control mode Press the [AUD] button. — 7— General features General features English Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "STANDBY" display. 2 Enter Speaker Setting mode Press the [Q] button. 3 Select the Speaker type Press the [ 4] or [ . ] button. Each time the button is pressed the setting switches as shown below. Speaker type Display OFF "SP OFF" Removing the Faceplate For the OEM speaker "SP OEM" Press the Release button. For 6 & 6x9 in. speaker "SP 6/6x9" The faceplate is unlocked, allowing you to detach it. For 5 & 4 in. speaker "SP 5/4" • The faceplate is a precision piece of equipment and can be 4 Exit Speaker Setting mode damaged by shocks or jolts. For that reason, keep the faceplate its special storage case while detached. Press the [Q] button. • Do not expose the faceplate or its storage case to direct or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate Switching Display Switching the information displayed. Press the [CLK] button. Each time the button is pressed below. In Tuner source Information Information Display Track Time Disc name* "DNPS" Disc title* "D-TITLE" Track title* "T-TITLE" Clock *: Function of the KDC-4027/KDC-4027V Other models in this manual: Car Receivers - KDC-3027G (925.21 kb) Car Receivers - KDC-308A (925.21 kb) Car Receivers - KDC-308G (925.21 kb) Car Receivers - KDC-4027 (925.21 kb)
)
