Votes - 4, Average rating: 4.5 ( )

Manafacture: Kenwood File size: 373.23 kb File name: Language of manual:

Other manuals for this model:

Car Receivers - KDC-226 (501.94 kb)

Connect the wiring harness wires battery, ignition. 5. Connect the wiring harness 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 2CAUTION • If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. • If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the connect the connectors either to both the front output or to both the rear output terminals (do not mix For example, if you connect the + connector of the left speaker to a front output terminal, do not connect - connector to a rear output terminal • After the unit is installed, check whether blinkers, wipers, etc. on the car are • Mount the unit so that the mounting or less. — 13 — 13— 13 — —— Connecting Wires to Terminals Connecting Wires to Terminals P.CONT ANT. CONT. TEL MUTE FRONT • L FRONT • R REAR • L REAR • R – + REAR L RFuse (10A) KENWOOD disc changer control input (KDC-3026/2026 only) Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green PurpleIgnition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Battery If no connections are made, do not let the wire come out from the tab. 4 Front left output (White) (KDC-3026 only) Front right output (Red) (KDC-3026 only) To connect the Disc changer, consult your Disc changer manual. Power control wire (Blue/White) Motor antenna control wire (Blue) When using the optional power amplifier, connect to its power control terminal. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. Not Used Do not let the wire come out from the tab. Rear left output (White) Rear right output (Red) FM/AM antenna input To front left speaker To front right speaker To rear left speaker To rear right speaker — 14 — 14— 14 — —— Installation Installation Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (for example, the sound may Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in Japanese-Made Cars 1 Refer to the section "Removing the hard rubber frame" (page 16) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit (KDC-3026/KDC-2026/KDC-226 only) If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 Never insert the taptite screw . 16 mm) in any other screw than the one specified. and may cause damage — 15 — 15— 15 — —— Installation Installation ¦ Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on...

Download now

Please, enter two numbers from picture: