Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking. Never take measures especially those other than indicated by italic letters in “Possible Solution” described below because those are too dangerous for users to handle themselves. Problem Warning .Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause ignition or electric shock. Immediately stop using the unit and consult your dealer. .Never try to repair the unit by yourself because it is dangerous to do so. Customize English Possible cause a Possible solution Common No power to the unit Sound is not generated. Noise Noise is made in step with engine revolutions. The power cord (battery, power and ground) is connected in the wrong way. a Check the wiring. Fuse blows out. a Eliminate the cause of fuse blowout and replace the fuse with new one. Consult your dealer. MUTE is set to ON. a Set MUTE to OFF. The wiring of speaker lines are not correct, or a break or poor contact arises. a Check the wiring in accordance with the wiring diagram. (Installation Instructions) There is an electromagnetic-wave generator such as a cellular phone near the unit or its electrical lines. a Keep an electromagnetic-wave generator such as a cellular phone away from the unit and the wiring of the unit. In case that noise cannot be eliminated due to the wiring harness of the car, consult your dealer. The contact of the ground lead is poor. a Make sure that the ground lead is connected to an unpainted part of the chassis securely. Alternator noise comes from the car. a Change the wiring position of the ground lead. a Mount a noise filter on the power supply. CQ-C8413U/C8313U Troubleshooting Problem Some operations are not executable. No sound from speaker(s) The speaker channels are reversed between right and left. The sound field is not clear in the stereo mode. Central sound does not settled. The power fails unintentionally. Possible cause a Possible solution Some operations are not executable in particular modes such as menu mode. a Read the operating instructions carefully and cancel the mode. If the unit is still out of order, consult your dealer. BALANCE/FADER setting is not appropriate. a Readjust BALANCE/FADER. There is a break, a short circuit, poor contact or wrong wiring regarding the speaker wiring. a Check the speaker wiring. The speaker wiring is confused between right and left. a Perform the speaker wiring in accordance with the wiring diagram. The plus and minus terminals at right and left channels of speakers are connected reversely. a Perform the speaker wiring in accordance with the wiring diagram. The safety device works. a Consult your dealer, or your nearest Panasonic Servicenter. Common (continued) Radio Poor reception or noise The number of auto preset stations is less than 6. Preset stations cannot be stored. Antenna installation or wiring of antenna cable is faulty. a Check whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely connected to the chassis. No power is supplied to the antenna amplifier (when using a film antenna, etc.). a Check the wiring of the antenna battery lead. The number of receivable stations is less than 6. a Move to an area where receivable stations number is maximum, and try presetting. The contact of the battery lead is poor, or the battery lead is not always powered. a Make sure that the battery lead is connected securely, and preset stations again. CQ-C8413U/C8313U Problem Possible cause a Possible solution The disc is inserted upside down. a Insert a disc correctly. No playback or disc ejected There is a flaw or foreign material on the disc. a Remove the foreign material, or use a flawless disc. CDMP3/WMA Troubleshooting English Sound skipping or noise Sound skipping due to vibration Disc unejectable There is a flaw or foreign material on the disc. a Remove the foreign material, or use a flawless disc. The unit is not sufficiently secured. a Secure the unit to the console box. The unit is tilted at over 30° in the front-to-end direction. a Make the angle 30° or less. Something such as a peeled label obstructs the disc coming out. a Press and hold the [u] (OPEN) for more than 2 seconds when the face plate is open (disc forced ejection). In case that the disc forced ejection does not work, consult your dealer. The microcontroller in the unit operates abnormally due to noise or other factors. a Unplug the power cord and plug it again. In case the unit is still out of order, consult your dealer. No playback or disc ejected The CD-R/RWs that are playable on other devices are not playable on this unit. Sound skipping or noise The playability of some CD-R/RWs may depend on the combination of media, recording software and recorder to be used even if these CD-R/RWs are playable on other devices such as a PC. a Make CD-...