Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
1Turn the Double Action encoder to select a preset number, and press /ENTER. Adjusted/set contents of the selected number are recalled. •The User Preset screen can also be recalled in normal mode by pressing and holding PRESET for at least 2 seconds. Turning Media Xpander ON/OFF When the Media Xpander is on, you can adjust the Media Xpander level (refer to page 33). OFF (Initial setting) ON Equalizer Presets (Factory’s EQ) (FR-EQ) 10 typical equalizer settings are preset at the factory for a variety of musical source material. FLAT POPS ROCK NEWS JAZZ&BLUES ELECTRICAL DANCE HIPHOP&RAP EASY LISTENING COUNTRY CLASSICAL USER1 USER2 USER3 USER4 USER5 USER6 •By selecting User’s 1 to 6, you can recall the stored preset number in “Adjusting the Graphic Equalizer Curve” (page 31) or “Adjusting the Parametric Equalizer Curve” (page 30). Sound Field Adjustment The setting of Parametric EQ/Graphic EQ Adjustment, Time Correction and X-Over can be adjusted in this mode. Adjusting the Parametric Equalizer Curve You can modify the Equalizer settings to create a response curve more appealing to your personal taste. To adjust the Parametric Equalizer Curve, set the EQ mode to PARAMETRIC EQ. For details, refer to “Setting EQ mode” (page 32). 1After selecting EQ ADJ (Parametric EQ) from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. BAND1 BAND2 BAND3 BAND4 BAND5 BAND1 2Turn the Double Action encoder to select an item to adjust, then press /ENTER. FC LV Q FC (frequency) (level) (bandwidth) (frequency) Frequency Adjustment 3-1Turn the Double Action encoder to select frequency bands. Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps) BAND1: 20 Hz~80 Hz (63 Hz) BAND2: 50 Hz~200 Hz (150 Hz) BAND3: 125 Hz~3.2 kHz (400 Hz) BAND4: 315 Hz~8 kHz (1 kHz) BAND5: 800 Hz~20 kHz (2.5 kHz) Level Adjustment 3-2Turn the Double Action encoder to adjust the level. Adjustable level: –6 to +6 dB Bandwidth (Q) Adjustment 3-3Turn the Double Action encoder to set the bandwidth (Q). Adjustable bandwidth: 1, 1.5, 3 4To adjust another band, repeat steps 1 to 3 and adjust all bands. •The frequencies of adjacent bands cannot be adjusted within 4 steps. •While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers. •You can select the next band by pressing and turning the Double Action encoder. •The User Preset screen can be recalled in the normal mode by pressing and holding PRESET for 2 seconds. Adjusting the Graphic Equalizer Curve You can modify the equalizer settings to create a response curve more appealing to your personal taste. To adjust the graphic equalizer curve, set the EQ mode to GRAPHIC EQ. For details, refer to “Setting EQ mode” (page 32). 1After selecting EQ ADJ (Graphic EQ) from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. BAND1 BAND2 BAND3 BAND4 BAND5 BAND6 BAND7 BAND1 BAND-1 (63 Hz) / BAND-2 (150 Hz) / BAND-3 (400 Hz) / BAND-4 (1 kHz) / BAND-5 (2.5 kHz) / BAND-6 (6.3 kHz) / BAND-7 (17.5 kHz) 2Press /ENTER to activate the level adjusting mode. 3Turn the Double Action encoder to adjust the level. Adjustable output level: –6 to +6 dB 4To adjust another band, repeat steps 1 to 3, and then adjust all bands. •You can select the next band by pressing and turning the Double Action encoder. •The User Preset screen can be recalled in the normal mode by pressing and holding PRESET for 2 seconds. Adjusting the Time Correction Before performing the following procedures, refer to “About Time Correction” (page 34). 1After selecting TIME CORRECTION from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. 2.2ch (3WAY) System F-L (Initial setting) F-R R-L R-R (Mid-L) (Mid-R) (High-L ) (High-R) SW-L SW-R F-L (Mid-L) 4.2ch (FRONT/REAR/SUBW.) System F-L (Initial setting) F-R R-L R-R (Front-L) (Front-R) (Rear-L) (Rear-R) SW-L SW-R F-L (Front-L) 2Press /ENTER to activate the Time Correction input mode. 3Turn the Double Action encoder to adjust the distance (0.0 to 336.6 cm). L = (distance to farthest speaker) – (distance to other speakers) Refer to “Time Correction Value List” on page 34. 4Repeat steps 1 to 3 to set another speaker. By setting these values to make its sound reach the listening position at the same time as the sound of other speakers. •You can select the next band by pressing and turning the Double Action encoder. •The User Preset screen can be recalled in the normal mode by pressing and holding PRESET for 2 seconds. Adjusting the Crossover Settings (X-OVER) Before performing the following procedures, refer to “About the Crossover” (page 35). 2.2ch (3WAY) System 1After selecting X-OVER from the Sound Field Adjustment mode, turn the Double Action encoder to select the band adjustment, and then press /ENTER. 2.2ch (3WAY) System / NORMAL (L=R) Setting items: LOW / MID-L / MID-H / HIG...