Votes - 4, Average rating: 4 ( )

Manafacture: Directed Electronics File size: 239.54 kb File name: G33550_33650_4-03.pdf Language of manual:

Cut out the hole. With the tweeter assembled, route the wires through the hole and the pressure ring and slip the pressure ring over the tweeter assembly. Align the tweeter so the Directed logo faces the desired direction then push the pressure ring on to the rear of the tweeter assembly until the tweeter is snugly mounted to the panel. Connect the speaker wires observing the correct polarity and re-assemble the panel. © 2003 Directed Electronics, Inc Flush Mounting into Mounted Panels 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter loca6. tion. 2. Mark the center point of the 7. tweeter location. 3. If using a hole saw, first drill a pilot hole, then cut out the hole using a 8. standard 2-1/8" hole saw. 4. If not using a hole saw, use either the cardboard packaging for the tweeters or the surface mount trim ring as a template to mark the 9. proper size hole. Cut out the hole. 5. Remove the tweeter from the flush mount housing and insert the FIGURE 3—FLUSH MOUNTING MOUNTED PANELS proper length machine bolt through the center hole of the housing and connect to the spring steel X- bracket. (See Figure 3.) Connect the speaker wires observing the correct polarity. Press the X-bracket portion of the assembly through the hole until its legs spring open. Screw the bolt in until the tweeter housing is firmly mounted to the panel. (Make sure the arrow at the rear of the tweeter housing is pointing in the desired direction.) Insert the tweeter into the housing and attach trim ring. (Refer to the trim ring information at the end of this section.) © 2003 Directed Electronics, Inc Tweeter Surface Mounting 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. 2. Place the surface mount housing against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is the mounting screw hole. 4. Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet. FIGURE 4—TWEETER SURFACE MOUNTING 5. After removing the surface mount tweeter assembly trim ring, route the tweeter wires through the larger hole in the housing and connect to the speaker wires from the crossover. (See Figure 4.) 6. Insert the excess speaker wire into the hole and position the housing so the housing will not pinch the wires after final mounting. 7. Attach the housing using the supplied screws of the correct length for a solid mount. 8. Insert the tweeter into the housing and attach the trim ring. © 2003 Directed Electronics, Inc Removing Trim Rings Hold the tweeter housing while gently turning the trim ring in a clockwise direction until it releases. The trim ring can then be easily lifted away from the tweeter housing. Installing Trim Rings • F FFl llu uus ssh hh M MMo oou uun nnt tt A AAs sss sse eem mmb bbl lly yy - With the arrow in the tweeter housing facing up, place the trim ring into the CROSSOVER INSTALLATION housing with the Viper logo at the bottom and turn in a counter clockwise direction until the trim ring clicks into place. • S SSu uur rrf ffa aac cce ee M MMo oou uun nnt tt A AAs sss sse eem mmb bbl lly yy - Insert the trim ring into the housing and turn in a counter clockwise direction until the trim ring clicks into place. Review the Installation Precautions section of this guide before proceeding. Crossover Adjustment and Wiring Connections This Directed crossover has the ability to work in car audio systems from basic FIGURE 5—SINGLE AMPLIFIER single amplifier systems to the most sophisticated multiple amplifier systems with signal processors and amplifier channels dedicated to each speaker. . © 2003 Directed Electronics, Inc SPECIFICATIONS ...

Download now

Please, enter two numbers from picture: