Votes - 4, Average rating: 4.3
(
)
)
|
Photos and specs Hyundai H-CSX10A |
manual abstract
Since the subwoofer is a large, heavy enclosure, it is highly recommended that you mount it in the trunk compartment of your vehicle. Mark the location for the mounting hole screws by positioning the cabinet where you wish to install it. Use heavy duty bolts to secure it. After you tightened it down, try to shake it or move it. Then tighten the screws again. Remote control mounting: Select a mounting location that allows easy access to the control while driving. Using the subwoofer level remote control as a template, mark and drill holes in the mounting surface (pic. 1). Notes: • Verify that mounting location is safe for drilling and wiring, and it will not interfere with the mechanical and electrical components of the vehicle. • Mount the unit using the brackets to the vehicle body so it does not move with sudden braking. • Do not expose to excessive heat and humidity. • Do not allow liquid and small objects get inside the unit. 2 Connecting Follow all mounting and wiring instructions to ensure the integrity of existing wiring after installation. Before connecting: Disconnect the vehicle's battery before making connection to the +12 volt supply wiring. Power input terminal connecting 1. 2. 3. 4. 5. 6. 7. 9. Connect the ground terminal to the closest point on the chassis of the vehicle. Keep this ground wire to less than 39" (100 cm) in length. Use 8 gauge (or heavier) wire. Connect the remote terminal to the remote output of the head unit using 16 gauge (or heavier) wire. Connect an empty fuse holder within 18" (45 cm) of the car battery, and run 8 gauge (or heavier) cable from this fuse to the amplifier location. Check that the fuse holder is empty. Then connect the fuse holder to the "BATT+" connection on the amplifier. Connect all line inputs and outputs (if used) using high-quality cables. Connect all speakers, following the diagrams in this manual. Be sure to observe proper polarity to avoid audio phase problems. Insert fuse into battery fuse holder. Recheck all connections before powering up the subwoofer. Set all level controls to minimum position, and set all crossover control/switches to the desired frequency points. Power up the head unit and the subwoofer. Then set the volume control on the head unit to about 3/4 volume, and adjust the subwoofer's input level controls to just below the level of distortion. Further fine tuning of the various controls may be necessary to obtain best results. POWER NPUT -0 © -0 © -0 © 50Hi 1ЬОН/ (Ив 12c8 MODEL: H-CSX10A POWER STATUS RE [»«PROTECT GREEN-ON REMOTE LEVEL CONTROL L (•j) 0 о o HYUNDAI □ g Chassis ground point -to REMOTE TURN-ON terminal of head uinit Pic. 1 Notes: Separate audio and power wiring to avoid interference. All wires and connections must be insulated with electrical tape, and filter with protective connector shields where ever possible. Before replacing blown fuse check and verify that there is no short cut at all connections. Low level input connecting Low-level (RCA) input wiring is preferred for best audio performance. most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality cable. Connecting scheme see on the pic. 2. 3 © POWER INPUT GROUND REMOTE 0 © 0 ® 0 ® К POWER STATUS RED-PROTECT GREEN-ON 0 180 50H7 1ЭДН7 MB 120B MIN MAX MODEL: H-CSX10A REMOTE LEVEL CONTROL HIGH INPUT © о HYUNDAI □ ÇTf rr ¥ I To Audio Outputs j of head unit or signal processor Pic. 2 ОГ High level input connecting The high level input(s) should only be used when your receiver lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. Connecting scheme see on the pic. 3. Note: Inputs may be high level (from the receiver's speaker) or low level (from special low level outputs). Low level is preferred for best performance. Attention: Use only the low level or high level input, do not use both at one time. Remote control connecting Connecting scheme see on the pic. 4. Connect the remote control to REMOTE jack on subwoofer. Fuse connecting Power fuse protect both the amplifier and the electrical system of your car from fault conditions. If you must replace a fuse in your HYUNDAI powered subwoofer, use a fuse of exactly the same type and rating. Using a different type or rating of fuse may result in damage to your amp or vehicle or cause a fire. Pic. 3 Pic. 4 4 1 3 4 5 © POWER INPUT 0 © 0 0 BO )ST © ЬОН/ 150H? OdB 12dB MIN MAX MODEL: H-CSX10A POWER STATUS RED*PROTECT GREEN-ON REMOTE LEVEL CONTROL Functions and controls 1. Power terminals: GND (ground), REM, +12V. 2. PHASE switch Use this switch to help compensate for time alignment problems in the system. Such problems usually result from...