Votes - 4, Average rating: 3 ( )

Manafacture: Mountain Buggy File size: 1.01 mb File name: 0f76d078-d72d-489e-8ce9-1f1d3405c83a.pdf Language of manual:

Step 7. Adjusting Handle Height While pushing both handle buttons in, rotate handle to the desired height (Figure G). Step 8. Proper use of Seat Belt, Shoulder Straps, and Recline WARNING: Avoid serious injury from falling or sliding out. Always use seat belt. 1. Place child in stroller seat. Make sure T-shield is between the child’s legs. 2. When child is seated, place shoulder straps over the child’s shoulders and clip onto the waist ring. 3. Buckle the T-shield buckles into the side waist buckles. Adjust the waist and shoulder straps for snug fit (Figure H). G Handle Adjust Button Handle Adjust Button E F H Child Tray Levers Parent Tray Hole Shoulder Straps Handlebar Knob Waist Strap T-shield 5 To recline seat: To fully recline, unhook buckle on back of the seat (Figure I). To place seat in upright position, push seat forward and reconnect buckle located on back of seat. Extra webbing can be placed in the rear pouch so it does not hang down and drag. To adjust the recline position, adjust the buckle on the strap. WARNING: Child may slip into leg openings and strangle. Never use in a reclined carriage position unless the T-shield and shoulder straps have been readjusted to the new seat position. Step 9. Using the infant car seat adapter bar When the car seat adapter bar is properly installed onto “The Everyday Stroller,” it is designed to be used with the following infant car seat brands and models. Graco® Snug Rider,® Century® Avanta,® Evenflo® On My Way.® The trade names and trademarks of Graco,® Century,® and Evenflo® are the trademarks of their respective companies. WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. The front child tray must be removed before using the infant car seat adapter bar. Lift up the textile cover of the seat’s side tubes. Insert adapter bar with buttons on the inside. Push in the spring buttons while pushing adapter bar into the seat’s side tubes end (Figure J1). Release button and continue pushing in the bar until the spring buttons lock into the holes located on the inside of the seat’s side tubes. Pull on bar to make sure it is locked in place. To remove adapter bar push in spring buttons with your finger or pen and pull out the bar. Store adapter bar in the under seat basket when not in use (Figure J2). I J1 Rear Recline Strap Car Seat Adapter Bar Black Spacers Textile Cover Spring Lock Buttons J2 Adapter Bar Under Seat Basket 6 Mounting infant car seat onto the adapter bar Note: The stroller seat should be in the full recline position with the recline strap unbuckled prior to placing car seat on. With the car seat adapter bar installed on the stroller, position the infant car seat (WITHOUT CHILD) so its mounting notch aligns with bar. The car seat will be mounted rearward facing towards the handle of the stroller. Push firmly down on the car seat so the bar is in contact with the car’s seat locking device or mounting notch (Figure J3). Note: Some car seats do not lock onto the bar, they just rest on the adapter bar. Using the stroller’s recline strap reverse the strap and insert the recline strap around the tubing and slide into the car seat’s retention slots on both sides of car seat and buckle (Figure J4). Cinch tight the recline strap around the car seat to anchor in place (Figure J5). Check to make sure the car seat is mounted securely by rocking the car seat front to back. The car seat should not wobble. If it does check and adjust the tension of the recline/restraint strap and make sure that the car seat mounting notch is resting on the adapter bar (Figure J6). DO NOT CHECK THE CAR SEAT MOUNTING TO THE STROLLER WITH YOUR CHILD IN THE CAR SEAT. J3 Car Seat Locking Mounting Notch Adapter Bar J4 Car Seat Retention Slot Strap Around Frame Tube Only – Do Not Wrap Over Canopy Tube WARNING: Car seats may fall forward if the strollers retention strap is not used. Do not use the car seat without cinching tight the retention/recline strap around the car seat. J5 Car Seat Retention Slot J6 NOTE: For the Century Avanta models, remove the 2-black spacers from the car seat adapter bar. 7 If you are unable to securely attach the infant car seat, discontinue use and contact our Customer Service representative. Please refer to the infant car seat manufacturers instruction’s and warnings for harnessing your child in the car seat. Do not lift stroller by using the infant car seat handle. Care and Maintenance Check fasteners After one hour of use, check all fasteners to make sure they are secure. Adjust if necessary. Periodically check the stroller to ensure that it is in good operating condition. To clean seat and canopy: If light cleaning is required, use a soft cloth with warm water and mild soap then air dry. Do not put into washing machine. Do not put in dryer. DO NOT BLEACH. To clean frame: Wipe using a soft cloth with warm water and mild soap. Air dry. DO NOT USE polish or abrasives. WARNING: If you have any questions c...

Download now

Please, enter two numbers from picture: