Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
In moist rooms, especially in the vicinity of water (bath), the charging station 3 must be firmly fixed to the wall, to protect it from falling into water. • Pull the wall holder 4 downwards from underneath the charging station 3. • Using the screw openings of the wall holder 4, mark the spacing for the boreholes on the wall. Check to ensure that there is a mains power socket in close vicinity. • Before boring the holes, check to ensure that there are no electrical or water conduits behind the markings. • Affix the wall holder 4 using the plugs and screws. • When you have attached the wall holder 4, guide the power cable through the right or left recess in the wall holder 4 (see magnification on the fold-out side). Using the guide rails, slide the charging station 3 onto the wall holder 4. • Ensure that the power cable is not trapped and that it lies properly in the recesses. - 4 First use Before taking the appliance into use check to ensure that it is in a fault-free condition. If it is not, it may not be used. • Insert the power plug into a wall socket. • Before the first use, clean the new brush heads 1 with clear water. • Place a replacement brush head on the brush holder 2, open the cover of the charging station 3 and slide the brush holder 2 in. • Place the hand element on the charging station 3 so that it slides onto the spike in the base. • Allow the hand element to charge up for approx. 14 - 16 hours before using it for the first time. The charging light 5 on the front of the hand appliance glows red during the charging process. • Use the hand element repeatedly, and without charging the battery, until the performance is noticeably weaker or the toothbrush stops working and the charge indicator 5 blinks red. First then recharge the battery for 14 - 16 hours. When the appliance is fully charged, the charge indicator 5 glows green. • Charge and discharge the toothbrush completely 3 times. The battery will have then reached its full capacity. • You can now leave the hand element in the charging station 3 after every use, so as to always have full power available. For care of the batteries, we recommend the following: When the hand element is fully charged, remove the plug of the charging station 3 from the mains power socket. First reinsert the plug into the mains power socket and recharge the hand element when the movement of the toothbrush is noticeably weaker or the charge indicator 5 blinks. - 5 Fitting / removing brush heads To remove the brush head 1, turn it clockwise and then pull it upwards. To fit the brush head 1 place it slightly offset on the hand element and then turn it anti-clockwise. The brush head 1 must engage on being put back on. To avoid damage to the appliance, use only original brush heads. (For replacement brush heads, see the order card) Operation This toothbrush has 3 different performing levels: -“Clean”: normal speed level, orange LED 8 For cleaning the teeth. -“Soft”: slow speed level, green LED 7 For cleaning the teeth of people with sensitive gums. -“Pulse”: variable speed levels, yellow LED 6 For massaging the gums. • Press the on/off switch 9 once to switch the level “Clean” on. The “Clean” LED 8 glows. • Press once more to switch to the level “Soft”. The “Soft” LED 7 glows. • Press it a third time to switch to the level “Pulse”. The “Pulse” LED 6 glows. • To switch the toothbrush off, press once more on the on/ off switch 9. Brushing one’s teeth Warning Due to the unaccustomed operation some gum bleeding may initially occur, this is normal. Should this continue for more than two weeks, consult your dentist. - 6 • Place the brush head 1 on the hand element. • Moisten the brush under flowing water. • Apply some toothpaste to the moistened brush. Notice Wait until the appliance is in the mouth before switching it on, to avoid spray. • With the on/off switch 9 select the desired operating level. Notice This toothbrush has a 30 second interval timer, so that all four jaw quandrants can be cleaned equally. • Divide your jaw into four sections (quadrants): upper left, upper right, lower left and lower right. • Begin in one quadrant: Place the brush head 1 on your gums and move the brush upwards/downwards from the gums to over the crown of the tooth. Proceed in this manner on both the inside and the outside surfaces of the tooth. Start again from the gums for each individual tooth. - 7 Do not forget the back surfaces of the rear molars. To clean the chewing surfaces, direct the rotating brush head with light pressure over the chewing surfaces. • After 30 seconds the toothbrush interrupts its operation briefly twice, to signalise to you that you should start to clean the next quadrant. Clean all jaw quadrants with the same technique. • After two minutes the toothbrush stops its operation briefly 4 times. This informs you that you have complied with the dental recommendation of two minutes cleaning. • Press the on/off switch 9 repeatedly until the toothbrush stops. • First tak...