Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
See “Entering administrator mode” on page 5 for more information. 2. Hold +9 until the status LED flashes in blue. 3. Input a new administrator password (a minimum of eight digits and a maximum of 16 digits), and then press . The status LED flashes in green three times. Note: If the status LED flashes in red three times, it indicates that the new administrator password is less than eight digits or more than 16 digits. After the status LED flashes in blue, input an administrator password that contains eight to 16 digits. 4. Input the new administrator password again, and then press . The status LED stays in green for three seconds, indicating that the administrator password is successfully changed. Notes: • If the status LED flashes in red three times and then flashes in blue, go back to step 3. This problem is caused by one of the following reasons: – You wait longer than 10 seconds before inputting the new administrator password. – The new administrator password is incorrectly input. • If no activity is detected within two minutes in administrator mode, the secure hard drive will return to standby mode. Adding a new user password The secure hard drive enables you to have up to 10 user passwords. To add a new user password, do the following: 1. Enter administrator mode. See “Entering administrator mode” on page 5 for more information. 2. Hold +1 until the status LED flashes in blue. 3. Input a new user password (a minimum of eight digits and a maximum of 16 digits), and then press . The status LED flashes in green three times. Note: If the status LED flashes in red three times, this indicates that the new user password is less than eight digits or more than 16 digits. After the status LED flashes in blue, input a user password that contains eight to 16 digits. 4. Input the new user password again, and then press . The status LED stays in green for three seconds, indicating that the user password is successfully added. Notes: • If the status LED flashes in red three times and then flashes in blue, go back to step 3. This problem is caused by one of the following reasons: – You wait longer than 10 seconds before inputting the new user password. – The new user password is incorrectly input. • If no activity is detected within two minutes in administrator mode, the secure hard drive will return to standby mode. Changing the user password Note: If you have more than one user password, you can change only one user password at a time. To change the user password, do the following: 1. Enter user mode. See “Entering user mode” on page 6 for more information. 2. Hold +1 for five seconds until the status LED flashes in red. Chapter 3. Using the secure hard drive 3. Input the current user password, and then press . The status LED turns green for three seconds, and then it flashes in blue. Note: If the status LED flashes in red, go back to step 2. This problem is caused by one of the following reasons: • You wait longer than 10 seconds before inputting the new user password. • The current user password is incorrectly input. 4. Input a new user password (a minimum of eight digits and a maximum of 16 digits), and then press . The status LED flashes in green three times, and then it flashes in blue. Note: If the status LED flashes in red three times, this indicates that the new user password is less than eight digits or more than 16 digits. After the status LED flashes in blue, input a user password that contains eight to 16 digits. 5. Input the new user password again, and then press . The status LED stays in green, indicating that the user password is successfully changed. Note: If the status LED flashes in red three times and then flashes in blue, go back to step 4. This problem is caused by one of the following reasons: • You wait longer than 10 seconds before inputting the new user password. • The new user password is incorrectly input. Note: The administrator password can be used as a user password. An administrator password can be changed only in administrator mode. For more information, see “Changing the administrator password” on page 6. Deleting the user password(s) To delete the user password(s), do the following: 1. Enter administrator mode. See “Entering administrator mode” on page 5 for more information. 2. Hold 7+8+ for five seconds until the status LED flashes in blue. After that, the status LED flashes in green three times, and then flashes in blue. 3. Hold 7+8+ for five seconds again until the status LED becomes green for three seconds and then turns blue. This indicates that the user password(s) are successfully deleted. Attention: If you have more than one user password, all user passwords will be deleted at a time. Lock the secure hard drive To ensure the data security of your secure hard drive when you are away from your computer, you can manually lock the secure hard drive or use the auto-lock function. Manually lock the secure hard drive To manually lock the secure hard drive, hold until the status ...
Other models in this manual:Hard Drives Discs - External Hard Disk Drives (0A65619 - ThinkPad USB 3.0 Secure Hard Drive - 500GB) (654.61 kb)