Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Overview of the NXA-BASE/B The NXA-BASE/B (Battery Base) is a Modero accessory that allows a touch panel to function off the collective charge of two internally connected NXT-BP batteries (FG2255-10). The base provides both power and battery information to the panel via the panel interface connector (FIG. 2). This base is also sold as part of an NXA-BASE/B Kit (FG2255K) that contains one (1) battery base and two (2) batteries. The accompanying batteries can be charged through either the base or optional NXT-CHG Modero Power Station (FG2250-50). Refer to the 12" and 15" Modero Touch Panel Series Owner/ Reference Manual for more information. Specifications ATTENTION! Before beginning the installation of the battery base to a CV series touch panel (NXDT-CV7, -CV10, or -CV17), verify that the firmware on the panel is Build 27 or higher. This build incorporates the necessary updates for using the Modero with the NXA-BASE/B. This does not apply to other Modero touch panels. Refer to the touch panel’s instruction manual for detailed firmware update procedures. Installing the NXT-BASE/B to an NXT Modero Panel 1. Power Off the panel before attempting to use the NXA-BASE/B. 2. Place the empty battery base onto a flat/level surface. 3. Verify the alignment of the Panel Interface connectors between the panel (male connector) and base (female connector) (FIG. 2). 4. Carefully place the Modero panel over the base alignment pegs (FIG. 3). These pegs assist in aligning the panel to the base. 5. Gently apply downward pressure until the panel is securely mounted to the battery base. 6. Firmly grip both the panel (from side) and battery base (from below). ATTENTION! The battery base CANNOT be "hot-swapped". A panel receiving power through a connected PSN6.5 cannot have a Panel Interface connector from the battery base inserted into the bottom of the panel. POWER OFF the panel before installing the NXA-BASE/B. 7. Gently place the touch panel LCD facedown onto a soft cloth. This prevents scratching of the LCD while the battery base is secured. 8. Locate the captive fastners on the underside of the battery base (FIG. 4) by angling the base combo slightly forwards. 9. Push down on each fastener head by using a flat-head screwdriver to turn them clockwise until the NXA-BASE/B is securely attached to the underside of the NXT Modero touch panel. 10. After securing is complete, firmly grip both the panel LCD/base combo and gently place the unit back onto a flat surface. FIG. 1 NXA-BASE/B and NXT-BP Specifications Dimensions (HWD): NXA-BASE/B (FG2255) NXT-BP (FG2255-10) • 1.13" x 8.63" x 11.81" (2.86 cm x 21.91 cm x 30.00 cm) • 0.69" x 3.50" x 5.81" (1.75 cm x 8.89 cm x 14.76 cm) Power: • NXA-BASE/B: 2.7 A @ 12 VDC (max power draw while charging) • NXT-BP: Voltage - 11.1 Volts Weight: • Base unit: 1.25 lbs (0.567 kg) • Base and 2 batteries: 3.23 lbs (1.47 kg) NXA-BASE/B: Features • Charge current 2.5A @ 12 VDC • Charge time for two depleted batteries ~ 5 - 8 hours • The Modero unit plus battery base requires a PSN6.5 power supply • Operating Environment: 10° C (50° F) to 35° C (95° F) • Storage Temperature: -20° C (-4° F) to +60° C (140° F) NXT-BP Features: • Battery Usage: 4 to 8 hours (time is usage-dependent) • Charge Capacity: 6300mAh • Operating Environment: 10° C (50° F) to 35° C (95° F) • Storage/Discharge Temperature: -20° C (-4° F) to +60° C (140° F) Optional Accessories: • NXT-CHG Kit (FG2250-50K): 1 charger (FG2250-50) and 2 NXT-BP batteries (FG2255- 10) • NXT-BP batteries (FG2255-10) • NXT-CHG charger (FG2250-50) NXA-BASE/B NXT-BP Battery Base Modero Power Pack FIG. 2 NXA-BASE/B showing Panel Interface and connector locations FIG. 3 NXA-BASE/B shown aligning with NXT panel Panel Interface Battery Compartment pulls outwards connector (female) Alignment pegs Captive fasteners (secure base to panel) Front Back Panel Interface connector Alignment pegs Interface connector Captive fasteners (male) Top view Bottom view (female) Front Setup (simulated image) Front Setup (simulated image) Captive fasteners (secure base to panel) FIG. 4 NXT-BASE/B showing underside fastener locations Checking the NXT-BP Charge 1. Press the Battery Life Indicator button (FIG. 5) once to illuminate the Battery Life LEDs and display the percent charge remaining on the battery (this indication lasts for a few seconds). Battery Life (Charge) Battery Life Indicator button It’s recommended to fully charge the batteries before their initial use FIG. 5 NXT-BP Modero Power Pack (showing Battery Life Indicator and button) 2. Repeat the above step for the remaining NXT-BP battery. 3. Charge the batteries by inserting them within the battery base. It is recommended to fully charge the batteries before they are initially inserted into the base. Refer to the following section for more detailed information on this process. ATTENTION! If the 25% LED indicator is blinking, this indicates that the battery has less than 5% of a charge remaining. Installation of an NXT-...