Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Rugged #304 grade stainless steel forms the sturdy housing that withstands virtually all environmental challenges; including heat, humidity, vibration, and other stress factors. The steel cover is hinged to ease installation Electrically, the C-Charger is a paragon of efficiency and simplicity. It uses a ferroresonant transformer with integral selfregulation. It has been intelligently designed to be completely devoid of any complicated switching circuits that could possibly burn out. There are no tubes nor delicate electronics to fail or to cause radio frequency interference (RFI). By simplifying our design, Charles has increased reliability without sacrificing performance or usability. Voltage output to the batteries remains at a safe and constant DC level from full load to no load, even if AC power runs as high as 132 VAC or as low as 108 VAC. This automatic voltage regulation relieves strain on internal electrical components and lengthens the lifespan of the unit. All components are designed to operate safely and continuously in an ambient temperature as high as 122° F. AE Series Battery Chargers are available in 12, 24 and 32 Volt models and may be used with both lead acid and nickel cadmium battery banks. Features UL Listed DC ammeter and voltmeter Float/equalize switch Equalize light AC circuit breaker Terminal board Cannot discharge battery during * Isolated output: no direct AC to AC failure Stainless steel for corrosion resistance Ferroresonant transformer for reliability Sealed silicon diodes DC connection Isolated positive and negative: can be used as a negative voltage charger Two year limited warranty ¿Charles SOLID POWER Specifications AC Input 108-132 volts/60 Hz (220 volts/50 Hz optional) Operating Temperature 0° to 50° C (32° to 122° F) Storage Temperature -20° to 60° C (-4° to 140° F) Cooling Convection DC Output - Float 2.16 VPC for lead Acid, 1.45 VPC for nickel cadmium - Equalize 2.33 VPC for lead Acid, 1.55 VPC for nickel cadmium Current Limit Approximately 135% Enclosure 304 stainless steel hinged cover to facilitate installation Model Number D.C. Output Height Inches Width Inches Depth Inches Approx. Weight Amps System Voltage 12 Volt AE1206* б 12 11 g 8.5 12 AE1210* 10 12 11 g 8.5 14 AE1220* 20 12 11 g 8.5 22 AE1230 30 12 11 g 8.5 2б 24 Volt AE2406* б 24 11 g 8.5 14 AE2410* 10 24 11 g 8.5 22 AE2420* 20 24 16.5 15 8.5 38 AE2430 30 24 16.5 15 8.5 55 32 Volt AE3210 10 32 11 g 8.5 2б AE3230 30 32 16 17 14.5 74 VPC 2.5 2.4 2.3 2.2 2.1 2.0 1.3 1.8 Typical Output Curve 0 10 20 30 40 50 60 70 80 90 100 % OF RATED CHARGING CURRENT (AMPS) *UL Listed Optional Accessories * 0-24 hour equalize timer * Automatic 24 hour equalize timer * Low DC voltage alarm relay Ordering Information High DC voltage alarm relay Current failure relay AC power failure relay DC cranking disconnect relay AC pilot light When ordering, please specify: 1. Model number 2. AC input: voltage & frequency 3. Battery type and number of cells 4. Ampere-hour capacity of battery 5. Recharge time desired 6. Description of load 7. Options Ê&harles Contact your Charles sales representative for specific product information. US D-IND001-B01 Rev. 3 Charles Industries, Ltd. Industrial Group 5600 Apollo Drive Rolling Meadows, IL 60008 USA Voice: (847) 8G6-63GG Fax: (847) 8G6-6352 E-mail: mktserv@charlesindustries.com ISO 9000 REGISTERED QUALITY SYSTEM Float...