Votes - 3, Average rating: 4
(
)
)
|
manual abstract
All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353. SPECIFICATIONS Item Description Capability 6 and 12 VDC battery tester with charging system output Load Test Capacity 100 amps; 50~1000 cold cranking amps Display Meter Analog, 0~16 VDC (maximum) Test Cycle 10 seconds per test with 1 minute cool down; 3 tests in 5 minutes Battery Cable / Clamps 16-3/4 inch; Copper plated clamps Overall Dimensions 12-3/4 (L) x 6 (W) x 3 (D) inches Features Carrying handle and four rubber feet Save This Manual You will need the manual for the safety warnings and precautions, operating and maintenance procedures. Keep your invoice with this manual in a safe and dry place for future reference. SAFETY PRECAUTIONS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. 4. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 5. Do not use the power tool if the Power Switch does not turn it on or off. Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced. 6. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. SKU 90636 For technicial questions, please call 1-800-444-3353. Page 2 7. Maintain tools with care. Keep clean. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 8. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 9. Maintain labels and nameplates on this tool. These carry important information. CAUTION! If unreadable or missing, contact Harbor Battery acid may cause severe Freight Tools for a replacement. injury to eyes; always wear ANSI approved safety goggles. Avoid 10. Always wear ANSI approved safety touching eyes while working with or impact eye goggles and heavy work near a battery. In case of accidental gloves when using this tool. Using contact, rinse eyes with clean personal safety devices reduce the risk water for at least 5 minutes and for injury. Safety impact eye goggles and see a doctor immediately. heavy work gloves are available from Harbor Freight Tools. 11. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use this tool in areas near flammable chemicals, dusts, and vapors. Do not use this product in a damp or wet location. WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. SPECIFIC SAFETY RULES FOR THE BATTERY TESTER 1. When connecting the Battery Cables to the battery, avoid creating sparks (always connect and disconnect clamps exactly as described in rule number 2, below, and on page 4), especially when the battery is being charged. Explosive gases are created during charging. Sparking could also damage the vehicle electrical system. 2. Be certain of the test battery polarity before connecting the test Cable Clamps. The red Cable Clamp (A) goes to the positive terminal of the battery.The black Cable Clamp (B) goes to the negative terminal of the battery. 3. When placing the Battery Tester in the vehicle (on the frame, engine, or fender), take special care that the metal housing of the Battery Tester does not come in contact with either terminal of the battery or other electrical connections. 4. Do not drop the Battery Tester as it may affect proper operation. 5. Do not smoke or have open flames near the battery. SKU 90636 For technicial questions, please call 1-800-444-3353. Page 3 6. Reversing Battery Tester Cable Clamps on the battery will damage the tester. 7. Do not connect the Battery Tester to the battery while the battery is being charged. Turn the engine off before connecting. 8. Do not touch the cooling vents on the Battery Tester immediately after testing the battery. They become very hot. UNPACKING When unpacking, check...