Votes - 0, Average rating: 0
(
)
)
|
manual abstract
9 To clean the compartment, lift it at the bottom and take out. Taking out glass shelf above vegetable container Fig. The glass shelf can be taken out and disassembled for cleaning. Note Before taking out the glass shelf, pull out vegetable container. Removing the container Fig. , Pull out the container all the way and lift to detach it. To insert the container, place on the telescopic rails and push into the appliance. Attach the container by pressing it down. en Odours If you experience unpleasant odours: 1. Switch off the appliance with the On/Off button. Fig. 2/1 2. Take all food out of the appliance. 3. Clean interior ( see chapter “ Cleaning the appliance”) . 4. Clean all packages. 5. Seal strong smelling food in order to avoid odours from forming. 6. Switch the appliance on again. 7. Store food in the appliance. 8. Check whether the formation of odours is still occuring after 24 hours. Light ( LED) Your appliance features a maintenance- free LED light. These lights may be repaired by customer service or authorised technicians only. en Tips for saving energy Operating noises ¦ Install the appliance in a dry, well ventilated room! The appliance should not be installed in direct sunlight or near a heat source ( e.g. radiator, cooker) . If required, use an insulating plate. ¦ Select 560 mm cavity depth. A smaller cavity depth will result in a higher energy consumption. ¦ Allow warm food and drinks to cool down before placing in the appliance. ¦ Thaw frozen food in the refrigerator compartment and use the low temperature of the frozen food to cool refrigerated food. ¦ Open the appliance as briefly as possible. ¦ Occasionally clean the rear of the appliance to prevent an increased power consumption. ¦ The arrangement of the fittings does not affect the energy rating of the appliance. Quite normal noises Droning Motors are running ( e.g. refrigerating units, fan) . Bubbling, humming or gurgling noises Refrigerant is flowing through the tubing. Clicking Motor, switches or solenoid valves are switching on/off. Preventing noises The appliance is not level Please align the appliance with a spirit level. If required, place something underneath. Containers or storage areas wobble or stick Please check the removable parts and re- insert them correctly if required. Bottles or receptacles are touchingeach other Move the bottles or receptacles slightly away from each other. en Eliminating minor faults yourself Before you call customer service: Please check whether you can eliminate the fault yourself based on the following information. Customer service will charge you for advice – even if the appliance is still under guarantee! Fault Possible cause Temperature differs greatly from the set value. Remedial action In some cases it is adequate to switch off the appliance for 5 minutes. If the temperature is too high wait a few hours and check whether the temperature has approached the set value. If the temperature is too low check the temperature again the next day. Displays do not illuminate. Power failhas been the mains not been inserted properly. ure; the fuse switched off; plug has Connect mains plug. Check whether the power is on, check the fuses. The light does not function. The LED lis defectivAppliance too long. Light is safter appright e. See chapter “Light (LED)” section. was open witched off ox. 10 min. When the appliance is closed and opened, the light is on again. en Fault Possible cause Remedial action Bottom of The condensation Clean the condensation channel the refrigerator compartment is wet. channel or drainage hole are blocked. and the drainage hole. See chapter Cleaning the appliance. Fig. 3 The refrigerating unit is switching on more frequently and for longer. Appliance opened frequently. The ventilation openings have been covered. Do not open the appliance unnecessarily. Remove obstacles. The temperature in the refrigerator compartment is too cold. Temperature has been set too low. Increase the temperature. Appliance is not cooling, temperature display and light are lit. Showroom mode is switched on. Hold down temperature selection button fig. 2/ 3 for 10 seconds until an acknowledgement signal sounds. After a short time check whether your appliance is cooling. Appliance self-test Your appliance features an automatic self-test program which shows you sources of faults which may be repaired by customer service only. Starting the appliance self-test 1. Switch off the appliance and wait 5minutes. 2. Switch on appliance and hold down the super button, Fig. 2/2, for 3- 5 seconds within the first 10 seconds until an acoustic signal sounds. The self- test programme starts. While the self-test is running, a long acoustic signal sounds. When the self-test ends and an acoustic signal sounds twice, your appliance is in working order. If the Super button flashes for 10 seconds and 5 acoustic signals sound, there is a fault. Inform customer service. Ending the appliance self- test When the programme has ended, t...