Votes - 0, Average rating: 0
(
)
)
|
manual abstract
¦ Never use oven cleaning products on ceramics. If oven cleaner is spilled on this accidentally, immediately remove it using lots of water and a sponge. Cleaning the oven's enamelled bottom and walls Use a cleaning cloth and hot water with a little soap or vinegar. If very dirty, use a fine steel scourer or a special oven cleaning product. These must only be used when the oven interior is cold. Do not use metal scourers or special oven cleaning products on self-cleaning surfaces. Light The oven light can be turned on manually to facilitate cleaning. Connecting the oven light Turn the function control knob to the Nsetting. The light will come on. The temperature control knob must be turned off. Turning the oven light off Turn the function control knob to the Uposition. Unhooking and hanging the oven door The front panel can be unhooked to help remove the oven door and clean the glass panels. The oven door hinges are fitted with a locking lever. The door cannot be unhooked if the locking lever is closed (figure A) . Once the locking lever has been opened to unhook the door (figure B) , the hinges will be locked in position. This prevents the door from suddenly closing. : Risk of injuries. ! The hinges may close suddenly if they are not locked in position by the lever. Note that the locking levers are always closed, apart from when unhooking the door, when the levers must be open. 9 Unhooking the door 1. Fully open the oven door. 2.Remove both locking levers located on the right and left hand sides (figure A). 3. Fully close the oven door as far as possible (figure B). Grip the left and right hand sides of the door with both hands. Close the door slightly more and remove it. Hanging the door Rehang the door by following the same steps but in reverse order. 1.When refitting the door, check that both hinges are positioned exactly inside their respective openings (picture A). 2. The bottom groove of the hinges must fit snugly on both sides. The door may be left crooked if the hinges are not mounted properly. 3. Reclose the attachment levers (picture C). Close the oven door. : Risk of injuries.! Do not touch the hinges; the door might accidentally fall or a hinge might suddenly close. Notify the Technical Assistance Service. Fitting and removing the glass panels The glass panels of the oven door can be removed to make cleaning easier. Dismantling 1.Unhook the oven door and place it on a cloth with its handle pointing downwards (Figure A). 2. Firstly screw the two bottom screws followed by the two top screws clockwise (Figure B). 3.Remove the cover (Figure C). The dismantled items should not be washed. Clean the glass using a glass cleaning product and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, or sharp or abrasive cleaning aids or detergents. Installing 1. Reattach the cover (Figure A). 2. Firstly screw the two bottom screws followed by the two top screws (Figure B). 3.Refit the oven door. Once the glass panels have been correctly fitted, the oven is ready to use. T r ou bles hoo tin g Quite often, when there is a malfunction, it is usually a small irregularity which is easy to rectify. Before contacting the Technical Assistance Service, try to determine the cause of the fault using the following table. Troubleshooting table Fault Possible Solution/ advice cause The oven does The fuse has Check the state of the fuse in not work. blown. the fuse box. Power cut. Check that the light in the kitchen and other household appliances are working. A zero flickers Power cut. Confirm with the 0 button. on the indicator. The oven does There is dust Turn the control knobs several not heat up. on the con- times in both directions. tacts. Error messages When the display panel shows an error message with “ , press the 0 button. The message will disappear. The set time function will be deleted. If the error message does not disappear, call the Technical Assistance Service. The following error messages can be solved by the user. Error Possible cause Solution/ advice message “ A button has been Press all of the buttons one pressed for too long by one. Check if any button or has got stuck. is stuck, covered or dirty. : Risk of electric shock. ! Incorrect repairs can be dangerous. Repairs can only be carried out by qualified personnel from the Technical Assistance Service. Changing the oven bulb If the oven light bulb is damaged it must be replaced. Special 25 W, E14, 220 V- 240 V heat-resistant light bulbs (to 300 . C temperature) can be obtained from the Technical Support Service or in specialist shops. Only use this type of bulb. : Risk of electrical discharge and the resulting shock. ! Disconnect the appliance from the mains. Ensure that this is turned off. 1. Place a dishcloth into the cold oven to avoid damage. 2. Remove the glass protection by unscrewing it to the left. 3. Replace the bulb with a similar bulb. 4. Screw the protection g...