Votes - 0, Average rating: 0
(
)
)
|
manual abstract
The noise reduces automatically when the appliance reaches its operating temperature. The humming noise is emitted by the motor (compressor). When the motor switches ON, the noise may briefly increase in volume. The bubbling, gurgling or whirring noise is emitted by the refrigerant as it flows through the pipes. The clicking noise can always be heard when the thermostat switches ON/OFF the motor. Cracking noises may occur if ... - the automatic defrosting is operating. - the appliance is cooling down or warming up (material expansion). A multi-zone or No-Frost appliance may cause a low hissing noise emitted by the air flow inside the appliance. If these noises are excessively loud, the causes are probably not serious and are usually very easy to eliminate. The appliance is not level Please level the appliance with the aid of a spirit level. Use the height-adjustable feet or place packing under the feet. The appliance is not free-standing Please move the appliance away from kitchen units or other appliances. Drawers, baskets or shelves are loose or stick Please check the detachable components and, if required, refit them. Bottles and/or receptacles are touching each other Please move bottles and/or receptacles away from each other. GB Minor problems and them Customer service contacted for every fault. are minor. Therefore, before you call customer service, please you can eliminate the fault yourself on the following information. A technician who is called out to rectify a minor fault will charge the customer, even if the appliance is still under guarantee. If the display, Fig. 2/9, does not illuminate: check that the power is ON, that the plug is correctly inserted in the socket and that the appliance is switched ON. If "E1" (flashing) (Fig. 2/9) is displayed while the appliance is being switched on: The temperature in the refrigerator compartment is very high. A few minutes after switching on the appliance, press the Cooler button to display the set refrigerator- compartment temperature. Otherwise, "Al" (freezer compartment is warm) or the set freezer-compartment temperature is displayed. If "E2" (flashing) (Fig. 2/9) is displayed while the appliance is being switched on: The temperature in the freezer compartment is very high. A few minutes after switching on the appliance, press the Freezer button to display "Al" and then the set freezer- compartment temperature. Otherwise, the set refrigerator-compartment temperature is displayed. If the refrigerator-compartment light does not function: – The light bulb is defective. Pull out the mains plug and remove the cover (Fig. A/A). Replace the defective light bulb with a light bulb of the same type (max. 15 W, 230 V, E14 holder). – The light switch is sticking (Fig. A/B). Check whether it can be moved. If not, please call customer service. If the display, Fig. 2/9, flashes but the acoustic signal is not emitted: the freezer compartment was too warm due to a power failure or a fault. When the Alarm button is pressed, the warmest temperature reached in the freezer compartment is indicated on display 9 (not flashing). This value is then cleared. Display 9 then indicates the programmed freezer compartment temperature without flashing. If a temperature greater than +3 °C is displayed, check the frozen food. If flavour, odour and appearance have changed, make a ready-made meal out of the food and refreeze. No longer store the frozen produce for the max. storage period. If the display fig. 2/9 flashes and the warning signal is emitted after the freezer compartment has been running for a prolonged period : Fault, freezer compartment is too warm ! The programmed freezer compartment temperature is displayed. To switch off the warning signal, press the "Alarm" button. Possible causes of the fault : - The gap above the appliance or in the base is blocked, - The freezer compartment door has not been closed properly, - Fresh food was frozen without "fast freeze", - Too much fresh food was frozen at once, - High ambient temperature. When the fault has been rectified, press the "Alarm" button; the display stops flashing when the freezer compartment has reached its operating temperature again. If the freezer section door has been kept open for a long time and the temperature inside now no longer reaches the pre-set level, so much ice has formed on the evaporator (source of cold temperature) that it cannot be defrosted by the fully automatic defrosting system. In this case take the Minor problems and to rectify them frozen goods out of the freezer, wrap them well to keep them cold and them somewhere cool. Switch off the appliance and open the freezer section door. After about 12 hours the ice on the cooling system will have thawed. Switch the appliance on again put the frozen goods back inside. If you are not able to rectify the problem with the help of the suggestions listed here, please call Customer Service. Do not open the door more often than necessary, so that the cold tempe...
Other models in this manual:Refrigerators - X5KXNSM361/02 (278.77 kb)
Refrigerators - X5KXNSM401/01 (278.77 kb)