Votes - , Average rating:
(
)
)
Manafacture: Bosch
File size: 359.82 kb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
There are no user serviceable parts on the inside. Cable repairs and replacements must be carried out exclusively by an Authorised Technical Service Centre. • This appliance has been designed exclusively for domestic use. Before using it for the first time, wash all of the Before using it for the first time, wash all of theBefore using it for the first time, wash all of theBefore using it for the first time, wash all of theBefore using it for the first time, wash all of theBefore using it for the first time, wash all of theaccessories and operate it once without any coffee. accessories and operate it once without any coffee.accessories and operate it once without any coffee.accessories and operate it once without any coffee.accessories and operate it once without any coffee.accessories and operate it once without any coffee. PREPARING DRIP-FED COFFEE (Fig. 2. - 6.) 1. Fill the tank (9) with cold water. A quantity of less than two cups is not recommended. 2. Open the filter holder as shown in: (figure 1) 3. Place the permanent filter (8) into the filter holder (7). Put in one tablespoonful of coffee for each cup of water. Note: • This coffee maker can also be used with n. 1x4 paper filters. • For correct operation, do not use coffee with too fine a grind. 4. Place the jug (2), with its lid fitted, on to the hot plate (1), plug the coffee maker into the mains and press the switch (5) (figure 4). The pilot lamp indicates that the coffee maker is working. A cup of coffee can be served before the brew cycle has finished. Whenever the jug is removed from the hot plate, the drip feed will stop temporarily. Place the jug back on the hot plate within 20 seconds. NOTE: To keep the taste of drip-fed coffee constant, we recommend that the drip-feed and espresso coffee maker modes should not be used simultaneously PREPARING ESPRESSO (Fig. 7 - 17) 1. Plug the appliance into the mains and make sure that the ON/OFF switch (10) is off and that the steam regulator (11) is closed. 2. Fill the water tank (9) with cold water (fig. 2) 3. This coffee maker is equipped with a BARCREAM device (19) which fits inside the filter holder. This disc ensures that creamy coffee is produced. (fig. 7) Due to the way it works, you will see a small amount of residual water inside the filter. Place the BARCREAM disc into the filter holder. Fill the filter using the coffee scoop (1 measure = 1 cup -2 measures = 2 cups) and place it inside the filter holder on top of the BARCREAM disc. Clean away any coffee that might be around the edge of the filter holder. CK7360-2 11 23/4/04, 11:25 4. Fit the filter holder into its housing (fig. 9). Turn the filter holder to the right until it stops. Do not force it. 5. To prepare coffee, press the ON/OFF switch (12) (figure 10). The red ON lamp (13) will light up. When the green temperature reached lamp (17) lights up, the coffee maker will have reached the right temperature to make the coffee. Press the espresso switch (16) (figure 13) to activate the coffee outlet. Press the espresso switch (16) again in order to stop the coffee from flowing. Attention: Do not release the filter holder (20) while the switch (16) is still ON. 6. Thanks to the appliance’s self-priming system there is no special procedure required when the water tank runs dry or if the coffee maker is not used for prolonged periods. PREPARING CAPPUCCINO The steam can be used to preheat cups, warm liquids or prepare cappuccino coffee. A cappuccino is espresso coffee with a little milk and a layer of froth. This froth made with cold milk in a jug, using the steam nozzle and then added to the espresso coffee. In order to avoid excess pressure on the inside of the filter, it is advisable to remove the filter holder before using the steam. Make sure that button (12) is ON (fig. 10). Next, press the steam function switch (14) (figure 11) and you will see the function lamp (15) light up. When the green pilot lamp (17) lights up, this indicates that steam has reached the right temperature. 1. Turn the steam regulator knob (11) clockwise, (fig. 14) and place a container below the steam nozzle (21) (figure 15). When the water inside the pipe finishes coming out, place the nozzle inside the jug of milk and turn the steam control knob again so that steam comes out. 2. Lift the jug up and down slightly. Try not to let the liquid go above the top of the nozzle as this will prevent air from entering. To obtain frothy milk, place the steam pipe just on the surface of the milk. 3. Add the frothy milk to the coffee. If you want you can sprinkle it with cinnamon, nutmeg or grated chocolate and decorate it with a stick of cinnamon. Important: Clean the nozzle of any leftover milk when you have finished preparing the frothy milk. It is advisable to give the nozzle a quick burst of steam to clean it out. 4. Clean the steam nozzle regularly but always with the appliance unplugged and cold (fig. 19). Remove the accessory from the steam pipe and clean the outside of t...