Votes - 1, Average rating: 3
(
)
)
|
manual abstract
To support it, use firm and solid pads that are inflammable. Never use the packaging materials for supporting. Level the appliance with the adjustable legs whenever necessary. Turn clockwise to raise the refrigerator, and anticlockwise to lower it. Do not expose the appliance to direct sunlight or heat source. Do not expose the appliance to rain and moisture. Keep the appliance dry and clean to prevent rust and deterioration of electric insulation. To prevent risk of injury and accident, do not place heavy load and water container on top of the refrigerator. 10cm minimum clearance above Distance 10cm minimum clearance at rear 10cm minimum clearance at both sides Removing & Replacing Door NOTE To avoid injury, property loss or damage to the refrigerator, make sure to remove all food from door racks and then remove bottle bin(s), unplug the refrigerator and shut off water supply before removing and replacing a door.To avoid injury or property loss, remove or replace the door with the help of 2 persons or more. The following instructions should be observed.Be careful to prevent the door from falling onto you when lifting the door from the hinge.To prevent the risk of suffocation, keep children and pets away from the drawers, in case they may get entrapped in the drawers. Removing and replacing the right door of refrigerator compartment Unscrew the upper right hinge cover by means of screwdriver and then remove the hinge cover. Unscrew the upper right hinge by means of hexagonal screwdriver and then remove the hinge. Remove the middle hinge if necessary. Replace the door in a reverse sequence of removal. Removing and replacing the left door of refrigerator compartment Unscrew the upper left hinge cover by means of screwdriver and then remove the hinge cover. Unscrew the upper left hinge by means of hexagonal screwdriver and then remove the hinge. The appliance should be placed in a well ventilated room. 10cm minimum clearance at both sides and at rear is required. > 12 > 11 Installing Bottom Trim Open the door of refrigerator compartment and take out the bottom trim. Fasten it to the bottom of refrigerator with screws as illustrated. Wear a pair of gloves to protect your hands when removing or installing the bottom trim and adjustable legs of the refrigerator. Installation of legs requires the joint efforts of at least two adults. Don’t attempt to handle it by yourself. Make sure the appliance is not tilted too much so that it overbalances.Before moving a refrigerator, the adjustable NOTE legs should be removed to prevent floor damage. Installing front cover of delicatessen drawer Open the door of refrigerator compartment. Take out the front cover of delicatessen drawer from the crisper cover. Then place the rotary shaft at both ends of the drawer into the supporting slot of the slide guide, and turn the front cover of delicatessen drawer down. Preparation Preparation Installing Legs Take out the accessory bag containing the legs from the refrigerator compartment. The appliance should be tilted.by one person and the legs should be installed as illustrated by the other person. NOTE Leg Reserved hole Removing & Replacing Door Handle Take out the door handles from the refrigerator compartment (2 longer handles to be installed on the refrigerator and 1 shorter handle to be installed on the freezer). The following instructions should be observed. Removing & Replacing Refrigerator Door Handle Get 2 fasteners out of the accessory bag and place them in 2 reserved holes in the left door. Install a handle by attaching the reinforcing plate to the fasteners and then pushing the handle to the left into its place. Install the right handle in the same way. To remove the handle, push it to the right. Fastener Reinforcing plate 20 > 19 > About Refrigerator Compartment Refrigerator Compartment The refrigerator can be used for short-term food storage: The average temperature of the compartment is about 0~10°C (-2~3°C in the delicatessen drawer). Therefore it is only used for short-term food storage and not suitable for keeping food fresh for a long time. Height-adjustable Shelf The height of shelf can be adjusted to meet your storage needs. To adjust the shelf height, remove the shelf first. The steps are as follows: tilt the shelf up at front, and lift it up and out of tracks. To replace the shelf, with shelf front raised slightly, engage the lugs in tracks. Then lower shelf front until it locks into position. NOTE NOTE Make sure the shelf is installed securely and level to prevent shelf falling or food spills. Lift and remove Tilt up To remove Engaged the lugs Up Down To replace Humidity regulator How to Use the Crisper The appliance is equipped with a crisper for vegetable and fruit storage. You can set the humidity to meet your storage needs. Turn the humidity regulator (located at the upper right corner of the crisper) up to get a higher humidity suitable for storage of cucumber, grape, kiwifruit etc. Turn the humidity regu...