Votes - 3, Average rating: 3.7 ( )

Manafacture: Carrier File size: 820.13 kb File name: 356012EN.pdf Language of manual:

12345 The wires in the mains lead are coloured in accordance with the following code: Installation 19 135 Green and Yellow: Earth Brown: Live Blue: Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp 4 is secure over the outer sheath. 5. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted 2 . In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely. Door reversibility The door of the appliance opens to the right. If you want to open the door to the left, do these steps before you install the appliance: 1. Loosen the upper pin and remove the spacer. 2. Remove the upper pin and the upper door. 20 20 Installation 3. Unscrew the pins (B) and spacers (C). 4. Remove the lower door. 5. Loosen the lower pin. On the opposite side: 1. Install the lower pin. 2. Install the lower door. 3. Refit the pins (B) and the spacers (C) on the middle hinge on the opposite side. 4. Install the upper door. 5. Tighten the spacer and tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. B C C 50 mm min. 200 cm2 min. 200 cm2 Installing the appliance CAUTION! Make sure that the mains cable can move freely. Do these steps. Installation 21 1. If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure. 2. Drill the hinge cover A, as shown in figure. Apply the covers A and A1 (in the accessories bag) in to the middle hinge. 3. Install the appliance in the niche. Push the appliance in the direction of the arrow (1) until the upper gap cover stops against the kitchen furniture. Push the appliance in the direction of the arrow (2) against the cupboard on the opposite side of the hinge. x x A A1 2 1 22 22 Installation 4. Adjust the appliance in the niche. Make sure that the distance between the appliance and the cupboard front- edge is 44 mm. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Make sure that the clearance between the appliance and the cupboard is 4 mm. Open the door. Put the lower hinge cover in position. 5. Attach the appliance to the niche with 4 screws. 6. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 44mm4mmII Installation 23 7. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. 8. If the appliance must connect laterally to the kitchen furniture door: a) Slacken the screws in fixing brackets (H). b) Move the brackets (H). c) Retighten the screws. 9. Disconnect the parts (Ha), (Hb), (Hc) and (Hd) BEDCH H 24 24 Installation 10. Install the part (Ha) on the inner side of the kitchen furniture. 11. Push the part (Hc) on the part (Ha). 12. Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. ca. 50 mm ca. 50 mm 21 mm 90° 90° 21 mm Ha Hc Ha Hb 8 mm Noises 25 13. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). 14. Place the small square on the guide again and fix it with the screws supplied. Align the kitchen furniture door and the appliance door by adjusting the part Hb. 15. Press the part (Hd) on the part (Hb). Do a final check to make sure that: • All screws are tightened. • The sealing strip is attached tightly to the cabinet. • The door opens and closes correctly. Ha K 8 mm Hb Hb Hd NOISES There are some sounds during normal running (compressor, refrigerant circulation). 26 26 Noises OK SSSRRR! CLICK! HISSS! BRRR! CRACK! BLUBB! CLICK!CLICK! BRRR! BRRR! BLUBB!BLUBB! Environmental concerns 27 HISSS! HISSS! SSSRRR!SSSRRR! CRACK! CRACK! ENVIRONMENTAL CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you wi...

Download now

Please, enter two numbers from picture: