Votes - 3, Average rating: 3.7 ( )

Manafacture: Carrier File size: 632.86 kb File name: 355761EN.pdf Language of manual:

socket. Contact a qualified electrician. The lamp does not work. The lamp is in stand-by. Close and open the door. The lamp is defective. Refer to "Replacing the lamp". The compressor operates The temperature is not set cor-Set a higher temperature. continually. rectly. The door is not closed correctly. Refer to "Closing the door". The door has been opened too Do not keep the door open longer frequently. than necessary. The product temperature is too Let the product temperature de- high. crease to room temperature before storage. The room temperature is too Decrease the room temperature. high. The compressor does not This is normal, no error has oc-The compressor starts after a pe start immediately after curred. riod of time. pressing the COOLMATIC switch, or after changing the temperature. Water flows on the rear During the automatic defrosting This is correct. plate of the refrigerator. process, frost defrosts on the rear plate. Temperature cannot be COOLMATIC function switched Switch off COOLMATIC manually, set . on. or wait to set the temperature until the function has reset automatically. Refer to "COOLMATIC function".. The temperature in the The temperature regulator is not Set a higher/lower temperature. appliance is too low/high. set correctly. The door is not closed correctly. Refer to "Closing the door". The product temperature is too Let the product temperature de- high. crease to room temperature before storage. 18 18 Technical data Problem Possible cause Solution Many products are stored at the same time. Store less products at the same time. The temperature in the re- There is no cold air circulation in Make sure that there is cold air frigerator is too high. the appliance. circulation in the appliance. Replacing the lamp The appliance is equipped with a longlife LED interior light. Only service is allowed to replace the lighting device. Contact your Service Center Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center. TECHNICAL DATA Dimension of the recess Height 1780 mm Width 560 mm Depth 550 mm Voltage 230-240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATION WARNING! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Positioning WARNING! If you are discarding an old appliance that has a lock or catch on the door, you must ensure that it is made unusable to prevent young children being trapped inside. The appliance shall have the plug accessible after installation. Installation 19 Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical Connection CAUTION! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING! This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. 12345 Green and Yellow: Earth Brown: Live Blue: Neutral The wires in the mains lead are coloured in accordance with the following code: 135 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: 20 20 Installation 1. Connect the wire coloured green and yellow to the terminal marked either with the letter “E“ or by the earth symbol or coloured green and yellow. 2. Connect the wire coloured blue to the terminal either marked with the letter “N“ or coloured black. 3. Connect the wire coloured brown to the terminal either marked with the “L“ or coloured red. 4. Check that no cut, or stray strands of wire is present and the cord clamp 4 is secure over the outer sheath. 5. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted 2 . In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely. Ventilation requirements The airflow behind the appliance must be sufficient. 50 mm min. 200 cm2 min. 200 cm2 Installation of the carbon air filter The carbon air filter is an active carbon filter which absorbs bad odours and permits to maintain the best flavour and aroma for all foodstuffs without risk of odour cross contamination. Noises 21 On delivery the carbon filter is in a plastic bag to maintain it’s duration and characteristics. The filter should be placed behind the flap...

Download now

Please, enter two numbers from picture: