Votes - 4, Average rating: 4.5 ( )

Manafacture: AEG File size: 251.27 kb File name: 227496en.pdf Language of manual:

When you contact us we need to know: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of the fault - What is the fault? - When does the fault occur? 4. The model, production number and product identification number. This information can be found on the serial plate in the interior at the left of the appliance. • Model Name • Model Number (PNC) • Serial Number (S-No. ) 5. Date of purchase Customer Care Department For general enquiries regarding your AEG appliance or futher information on AEG products, please contact our Customer Care Department at the address below or visit our website at Customer Care Department AEG Domestic Appliances 55-77 High Street, Slough, Berkshire SL1 1DZ Tel: 08705 350 350* *calls to this number may be recorded for training purposes late in electrical components, which could cause an electrical shock! Hot vapours can lead to the damage of plastic parts. • The appliance must be dry before it is placed back into service. Warning! • Ethereal oils and organic solvents can attack plastic parts, e.g. – lemon juice or the juice from orange peel, – butyric acid; – cleansers which contain acetic acid. Do not allow such substances to come into contact with appliance parts. • Do not use any abrasive cleansers. 1. Remove frozen food and the food from the refrigerator. Wrap frozen food in several layers of newspaper. Store it in a cool place, well covered. 2. Switch the appliance off and remove the plug from the mains, or switch off. 3. Clean the appliance and the interior accessories with lukewarm water and with a little bicarbonate of soda added (5ml to 0,5 litre of water). Commercially available dish washing detergents may also be used. 4. Dry the appliance thoroughly. 5. Check the water drain hole on the rear wall of the fridge. Clear a blocked drain hole with the aid of the drain cleaning tool included with the appliance. 6. When everything is dry place the appliance Energy Saving Tips • Do not install the appliance or other sources of continuous warmth. High ambient temperatures cause longer, more frequent operation of the compressor. • Ensure sufficient air circulation at the appliance of the appliance. • Do not place first. • Do not leave the door open any longer than necessary. • Do not set temperature any colder than necessary. • Put frozen food in the fridge to defrost. The cold in the frozen food will then be used to cool the fridge. Something Not Working If the appliance is not functioning correctly, please carry out the following checks before contacting your local AEG Service Force Centre. Warning! Repairs should only be carried out by qualified service engineers. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Symptom Possible Cause Remedy Appliance is not switched on Switch on the appliance. Mains plug is not plugged in or is loose. Insert mains plug. Appliance does not work. Fuse has blown or is defective. Check fuse, replace if necessary. Socket is defective. Mains malfunctions are to be corrected by an electrician. Appliance cools too much. Temperature is set too cold. Turn the temperature control knob to a warmer setting. Temperature is not properly Please look in the "Initial Start adjusted. Up" section. Door was open for an exten- Open the door only as long as ded period. necessary. The food is too warm. A large quantity of warm food was placed in the appliance within the last 24 hours. Turn the temperature control knob to a colder setting. The appliance is near a heat Please look in the "Installation source. location" section. Please look in the "Changing Interior lighting does not work. Light bulb is defective. the Light Bulb" section. Carefully warm the leaking sections of the door seal with a hair dryer (not hotter than Heavy build up of frost, possi- Door seal is not air tight pos approx. 50 °C). At the same bly also on the door sibly after reversing the door). time shape the warmed seal by hand until Symptom Possible Cause Remedy The compressor does not start This is normal, no error has The compressor starts after a immediately after changing occurred. period of time. the temperature setting. Water on the floor or on sto- Water drain hole is blocked. See the "Cleaning and Care" rage shelves. section. If, after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for any in-guarantee service calls. Changing the light bulb Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it. Light bulb data: 220-240 V, max. 15 W 1. To switch off the appliance, turn the temperature control knob to position "0". 2. Unplug the mains plu...

Download now

Please, enter two numbers from picture: