Votes - 2, Average rating: 3.5 ( )

Manafacture: Briggs & Stratton File size: 1.31 mb File name: c741607a-8284-4a50-b6b8-4b16fc836ae3.pdf Language of manual:

Air Cleaner — Protects engine by filtering dust and debris out of intake air. Choke Lever — Used when starting a cold engine. Circuit Breakers (AC) — Each receptacle is provided with a "push to reset" circuit breaker to protect the generator against electrical overload. Fuel Tank — Capacity of five (5) U.S. gallons. Grounding Fastener — If required, please consult a qualified electrician, electrical inspector, or local agency having jurisdiction. Oil Fill Cap — Add oil to engine here. Recoil starter — Used to start the engine. Rocker Switch — Set this switch to "On" before using recoil starter. Set switch to "Off" to switch off engine. 120 Volt AC, 15 Amp Duplex Receptacle Fuel Tank Choke Lever Recoil Starter Rocker Switch Circuit Breakers (AC) 120 Volt AC, 20 Amp Duplex Receptacle Air Cleaner Grounding Fastener (not shown) Oil Fill Cap (not shown) 6 PowerBOSS™ 5000W Portable Generator ASSEMBLY ASSEMBLY Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel. If you have any problems with the assembly of your generator, please call the generator helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. Remove Generator From Carton 1. Set the carton on a rigid flat surface with “This Side Up” arrows pointing upward. 2. Carefully open the top flaps of the shipping carton. 3. Cut down corners at one end of carton from top to bottom and lay that side of carton down flat. 4. Remove all packing material, carton fillers, etc. 5. Remove the generator from the shipping carton. Carton Contents Check all contents against those listed below: • Main unit • Engine oil • Owner’s manual • Engine manual • Wheel kit If any parts are missing or damaged, call the generator helpline at 1-800-743-4115. INSTALL WHEEL KIT NOTE: While the wheel kit is designed to greatly improve the portability of your generator, it is not intended for over-the-road use. You will need two 1/2” or 13mm open end wrenches or a socket wrench with 1/2" or 13mm sockets and a 15/16” wrench to install this kit. Install the wheel kit as follows (Figure 1): 1. Place bottom of generator cradle on a flat surface. 2. Place axle stud through wheel retainer on cradle frame. 3. Use 15/16” wrench to secure axle stud to frame with 5/8-18 jam nut. 4. Install other axle stud in same manner. NOTE: Be sure to install wheel with raised hub inboard. 5. Tip unit and install wheel. Place flat washer over axle stud. Capscrew Handle Mounting Leg Jam Nut Wheel Retaining Pin Washer Axle Stud Nut Capscrew Nut Figure 1 — Install Wheel Kit Typical Generator Shown ASSEMBLY 5000W Portable Generator PowerBOSS™ 6. Retain wheel on axle stud with retaining pin. Install other wheel on remaining axle stud the same way. 7. Attach support leg using two 1/2” or 13mm wrenches with 20mm cap screws and lock nuts. 8. Center lifting handle on generator end of cradle. Attach handle using two 1/2” or 13mm wrenches with 45mm capscrews and hex nuts. BEFORE STARTING THE ENGINE Add Engine Oil • Place generator on a level surface. Add Fuel NOTE: This gasoline engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications). WARNING Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. WHEN ADDING FUEL • Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank. • Fill fuel tank outdoors. CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. • Refer to engine manual for oil fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. • DO NOT overfill tank.Allow space for fuel expansion. • Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. • DO NOT light a cigarette or smoke. 1. Use clean, fresh, regular UNLEADED fuel with a minimum of 85 octane. DO NOT use fuel which contains Methanol. DO NOT mix oil with fuel. • Refer to engine owner’s manual and follow oil 2. Clean area around fuel fill cap, remove cap. recommendations and instructions. 3. Slowly add regular unleaded fuel to fuel tank. Be careful NOTE: Check oil often during engine break–in. Refer to not to overfill.Allow about 1.5" of tank space for fuel engine owner’s manual for recommendations. expansion (Figure 2). NOTE: The generator assembly rotates on a prelubricated and sealed ball bearing that requires no additional lubrication for the life of the bearing. Figure 2 - Fuel Expansion Fuel Tank 1.5” Air Space 4. Install fuel cap and wipe up any spilled fuel. 7 PowerBOSS™ 5000W Portable Generator OPERATION USING THE GENERATOR System Ground The generator has a system ground that connects the generator frame components to the ground terminals on the AC output receptacle...

Download now

Please, enter two numbers from picture: