Votes - 0, Average rating: 0
(
)
)
|
manual abstract
five minutes per hour. If you want to end the AirFresh function, press the # button. Lighting The lighting can be switched on and off independently of the fan. Press the Abutton. Setting the brightness Press and hold the Abutton until the desired brightness is reached. Saturation display When the metal mesh grease filters or the activated carbon filter are saturated, a signal sounds for approx. 4 seconds after the fan is switched off. In addition, this symbol is indicated on the display: . If you have not yet done so, the metal mesh grease filters should be cleaned now. For instructions on how to clean the metal mesh grease filters, please refer to the section Cleaning and maintenance. While the saturation display is flashing, it can be reset. To do this, press the – button. Audible signal Switching on the acoustic signal When the fan is switched off, press the # and + at the same time for approx. three seconds. An acknowledgement signal sounds. Switching off the acoustic signal Repeat the "Switching on the acoustic signal" process. Control panel model 2 Control panel ...................... Explanation # Fan on/off 4 Noise reduction -Reduce the fan settings/fan run-on time/interval ventilation + Increase the fan settings/intensive setting 1, 2 . Direct selection of intensive setting 2 A Light on/off/dimming Setting the fan Switching on the appliance ¦ Press the # button. The fan starts at setting .. ¦ Press the + or - button to change the fan strength. Switching off Press the # button. Intensive setting You can use the intensive setting if there is a large build-up of odours and fumes/vapours. Press the . button. .. appears in the display. Press the - button to switch back to the intensive setting .‚. After approx. six minutes, the electronics automatically reduce the fan to a lower setting . If you want to end the intensive setting before this time expires, press the . button. Fan run-on time Press the - button until – appears. After approx. ten minutes, the fan switches off automatically. AirFresh function Press the - button until 3‚ appears. The fan runs for approx. five minutes per hour. If you want to end the AirFresh function, press the # button. Noise reduction function The noise reduction function reduces the fan noise. Switching on the appliance Press the 4 button. The function is possible in all fan settings, except in fan setting ‚. It also remains active after the fan is switched off. Switching off the appliance Press the 4 button. Lighting The lighting can be switched on and off independently of the fan. Press the Abutton. Setting the brightness Press and hold the Abutton until the desired brightness is reached. Saturation display When the metal mesh grease filters or the activated carbon filter are saturated, a signal sounds for approx. 4 seconds after the fan is switched off. In addition, this symbol is indicated on the display: . If you have not yet done so, the metal mesh grease filters should be cleaned now. For instructions on how to clean the metal mesh grease filters, please refer to the section Cleaning and maintenance. While the saturation display is flashing, it can be reset. To do this, press the – button. Audible signal Switching on the acoustic signal When the fan is switched off, press the # and + at the same time for approx. three seconds. An acknowledgement signal sounds. Switching off the acoustic signal Repeat the "Switching on the acoustic signal" process. Cleaning and maintenance : Risk of burns! The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning. : Risk of electric shock! Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box. : Risk of electric shock! Penetrating moisture may cause an electric shock. Do not use any high-pressure cleaners or steam cleaners. : Risk of injury! Components inside the appliance may have sharp edges. Wear protective gloves. Cleaning agents Observe the information in the table to ensure that the different surfaces are not damaged by using the wrong type of cleaning agent. Do not use ¦ harsh or abrasive cleaning agents, ¦ cleaning agents with a high concentration of alcohol, ¦ hard scouring pads or sponges, ¦ high-pressure cleaners or steam cleaners. Wash new sponge cloths thoroughly before use. Follow all instructions and warnings included with the cleaning agents. Area Cleaning agents Stainless steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth. Clean stainless steel surfaces in the direction of the grain only. Special stainless steel cleaning products are available from our after-sales service or from specialist retailers. Apply a very thin layer of the cleaning product with a soft cloth. Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a soft cloth/towel. Do not use any stainless steel clea...
Other models in this manual:Range Hoods - D39GL64S0B/01 (944.98 kb)
Range Hoods - D39MH64N0B/01 (944.98 kb)