Votes - 0, Average rating: 0 ( )

Manafacture: Bosch File size: 2.08 mb File name: Language of manual:

The filter mats are made from noncombustible metal. Caution: As the filter becomes more and more saturated with grease, not only does the risk of it catching fire increase but the efficiency of the extractor hood can also be adversely affected. Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Saturation indicator: F When the grease filter becomes saturated, the display symbol F appears. The grease filter should be cleaned straight away. Cleaning the metal grease filters: . In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned after 8 to 10 weeks. . The filters can be cleaned in a dishwasher. It is however possible that they will become slightly discoloured. . The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. . When cleaning the filters by hand, soak them in hot soapy water first of all. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. Removing and inserting the metal grease filters: Warning: The halogen bulbs must be switched off and cool. 1. Press the catch on the grease filters inwards and fold the filters down. Fig. 1. 2. Clean the filters. 3. Insert the clean filters back into the hood. 4. Cancel the F indication in the display. . Swith the motor off (stop position). . Press for some seconds at the same time 0 and T. A signal sounds and the display symbol ~ at the side goes out. Activated carbon filter: For neutralizing odours in recirculating mode. Saturation indicator: C When the activated carbon filter becomes saturated the display symbol C. Lights up and a signal sounds. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Filters and maintenance Inserting the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters (see "Removing and inserting the metal grease filters"). 2. ... Insert the activated carbon filter. Fig. 2. 3. Raise the activated carbon filter in front and rotate the closures by 90°. Fig. 3. 4. Insert the metal grease filters (see Removing and inserting the metal grease filters). 5. Cancel the C in the display. . Switch the motor off (stop position). . Press for some seconds at the same time 0 and T push buttons. A signal sounds on the display and the display symbol ~ at the side goes out. Removing the filter: Warning: The halogen bulbs must be switched off and cool. 1. Remove the metal filters. 2. Rotate the closures by 90° and remove the activated carbon filter downwards. Fig. 3. 3. Insert the metal grease filters. Replacing the activated carbon filter: . During normal operation (1 to 2 hours per day) the activated carbon filters should be replaced approximately 1 x year. . A replacement filter can be obtained from any authorized dealer. . Use original filters only. By doing so you will obtain maximum performance from your extractor hood. Disposing of the old activated carbon filter: . There are no pollutants in the activated carbon filters. They can therefore be disposed of as part of your normal domestic refuse. The electronic controls allow automatic control of the fat filters and the carbon filters (only when the hood is used in filtering version), so that the user does not have to remember when maintenance was last carried out. When the metallic fat filters have to be cleaned, then F on the display will flash. When the carbon filters have to be replaced, C on the display will flash. It is possible to interrogate the electronic system concerning how clean the fat filters are and how worn the carbon filters are, as follows: stop the motor and … … To find out how clean the fat filters are, press the 0 and – buttons at the same time. On the display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is and vice versa. … To find out how worn the carbon filters are, press the 0 and + button at the same time. On the display a number between 0 and 9 will appear, the smaller the number, the more worn the filter and vice versa. Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. Do not clean the extractor hood with abrasive sponges or with cleaning agents which contain sand, soda, acid or chlorine! . Clean the extractor hood with a hot soap solution or a mild window cleaner. . Do not scrape off dried-on dirt but wipe off with a damp cloth. . When cleaning the grease filters, remove grease deposits from accessible parts of the housing. This prevents the risk o...

Download now

Please, enter two numbers from picture: