Votes - 2, Average rating: 4
(
)
)
|
manual abstract
• The post motor filter is located on the rear of the vacuum. Remove the filter cover. • Remove the filter grill and take out the filter. • Rinse in lukewarm water, let air dry completely. Do not use a washing machine to rinse the filter. Do not use a hair dryer to dry it. Air dry only for 24 hours. • When filter is completely dry, replace post motor filter back into the filter grill and replace back into the unit. 5. When pulling out the power plug from the wall outlet, pull the plug not the power cord. OPERATING INSTRUCTIONS Assembling Your Vacuum Cleaner Note: Always remove the power plug from the wall outlet before assembling or removing accessories. 4 4. Fitting the Floor to Carpet Brush to the Telescopic Tube Push the telescopic tube into the floor brush as show in the illustration below. 1. Attaching the Flexible Hose into the Vacuum Connect the flexible hose into the air intake duct. Push in until you hear a “click”, indicating it is in its locked position. To remove the flexible hose first remove the power nozzle power cord from the receptacle for the power nozzle power cord, then depress locking button and remove hose. Connect the hose connecting power cord from the flexible hose to the power cord receptacle that is on the unit just below the air intake duct. 7 OPERATING INSTRUCTIONS 2. Insert the motorized brush power cord plug into the power socket on the flexible hose. To start motorized brush press the On/Off button that is located on the motorized brush. Telescopic TubePowerNozzleFloor to Carpet Nozzle1. Connecting the power nozzle with the telescopic tube: A) Depress the button on the telescopic tube and insert it into the slot on the power nozzle elbow. B) Push the telescopic tube down until you hear a "click" . (see illustration below). Using Power Nozzle Air intake ductPower cord receptacle Telescopic Tube 2. Fitting the Telescopic Tube to the Curved Wand / Hose ExtensionPush the telescopic tube into the curved wand / hose extension, as shown in the illustration below. Make sure that the telescopic tube locks in place. PlasticButton3. Extending the Telescopic Tube Push forward on the plastic button and pull the inner tube outward. Important: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged. PLEASE NOTE: The white pleated filter material in the HEPA Dust Cup Filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA Dust Cup Filter is properly "TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA filter be “TapCleaned” vigorously until no more dust can be removed, then rinsed under the faucet and allowed to air dry for 24 hours before refitting into the vacuum. (Fig. A) This should be done once a month or when suction appears to be reduced. Fig. AWarning: Allow 24 hours for drying before replacing in unit.Wash once a month or when suction appears reducedChanging & Cleaning the Pre-Motor FilterThe pre-motor filter is located underneath the dust cup container. This is a rinseablefilter but should be replaced every six (6) months. Never operate the vacuum without ALLthe filters in place. • Push the Power On/Off button to the "Off" position and disconnect the power cord from the wall outlet. • Remove the dust cup container. • Remove the pre-motor filter and rinse in lukewarm water, let dry completely. Do not use a hair dryer to dry it. Air dry only. • When filter is completely dry, replace pre-motor filter back into the unit and replace the dust cup container. 7. Vigorously “TapClean” the HEPA Dust Cup Filter on a hard surface until no more dust is observed falling out from between the pleats of the filter. See illustration at right. Ensure that the filter assembly is completely seated inside the dust cup (container) . Important: Do NOTuse the HEPA filter cartridge without the debris screen in place.10. Re-install dust cup into the vacuum and re-attach hose. 8. Reassemble the debris screen back onto the HEPA filter cartridge. 9. To replace the HEPA filter back into the dust cup container, hold the filter by the stem and insert it up into the dust cup container making sure that the top rim of the filter fits onto the top of the dust cup container and twist it clockwise to lock in place. 5 OPERATING INSTRUCTIONS 3. To rewind the power cord, press the cord rewind button with one hand and hold the plug of the power cord with the other hand to ensure that it does not whip causing damage or injury. Crevice Tool and Dusting Brush Motor Thermostat Important: This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum from the wall outlet and turn off the switch. Empty the dust cup, "TapClean" the dust cup filter and check for blockages in hose and suction inlet. Allow the unit to cool for a min...