Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
(Figure A) 2. Once the Mounting Bracket has been attached to a desired location, unscrew and remove the Retaining Ring (part #23) from the top of the Mini Air Filter. 3. Insert the top of the Mini Air Filter through the Mounting Bracket and secure by replacing the Retaining Ring. 4. Attach a 1/4” NPT Female hose connector to the air compressor supply hose. Then, wrap the threads of the 1/4” NPT Female hose connector with approximately 3” of Teflon tape. Next, connect the 1/4” NPT Female hose connector to the inlet side of the Mini Air Filter. 5. Attach a 1/4” NPT Male hose connector to one end of the outlet extension hose (to which you will connect a tool). Check to make sure the other end of the outlet extension hose is fitted with a quick coupler. Then, wrap the threads of the 1/4” NPT Male hose connector with approximately 3” of Teflon tape. Next, connect the 1/4” NPT Male hose connector to the outlet side of the Mini Air Filter. 6. Connect the quick coupler of the air outlet extension hose to the tool you are using. Turn on the air compressor and regulate the desired PSI to the tool by pulling up and turning the Pressure Adjustment Knob (part #1) on the Mini Air Filter clockwise for reduced air pressure, or counterclockwise for increased air pressure. Press down on the knob to lock. 7. The Mini Air Filter is now ready for use. NOTE: Depending on usage, periodically examine the Drain Cup (part #11) for accumulated water that is being separated from the compressed air system. See Step one for instructions on draining the excess fluid from the Drain Cup. AIR OUTLET 11 9 14 CLEANING AND MAINTENANCE 1. When the water level rises to the bottom edge of the Filter Mesh Mounting (part #9) within the Drain Cup (part #11) it is necessary to remove the excess fluid. To drain the fluid slowly turn the Water Valve Drain (part #14) counterclockwise until the fluid begins to flow from the Drain Cup. When all of the fluid has been drained turn the Water Valve Drain clockwise to tighten. 2. To clean, wipe with a clean, damp cloth, using a mild soap with water if necessary. Then, dry. SEE REVERSE SIDE OF THIS INSTRUCTION FLYER FOR PRODUCT WARNINGS, PRECAUTIONS, PARTS LIST, AND ASSEMBLY DIAGRAM. REV 01d; 07g SAFETY WARNINGS AND PRECAUTIONS 1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. 2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children to handle this product. 3. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 4. USE EYE PROTECTION. Wear ANSI-approved safety impact eye goggles. The ANSI-approved safety impact goggles are available from Harbor Freight Tools. 5. CHECK FOR DAMAGED PARTS. Before us ing this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 6. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 7. MAINTENANCE: Service and maintenance should be performed regularly by a qualified technician. 8. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which this product was designed. Do not use a smaller tool to do the work required by a larger industrial size tool. Do not use this product for a purpose for which it was not intended. 9. The brass components of this proDUCT contain lead, a chemical known TO THE State of California to cause BIRTH defects (or other reproduCtive harm). (California Health & Safety code § 25249.5, et seq.) SAVE THIS INSTRUCTION SHEET You will need this instruction sheet for the Operating, Maintenance Procedures, and Safety Warnings and Precautions. Keep your invoice with this instruction sheet. Write the invoice number on the the front of this instruction sheet. Keep this instruction sheet and invoice in a safe and dry place for future reference. 22 1 23 2 15 16 3 17 4 5 18 19 6 20 7 8 9 10 11 12 21 13 14 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PARTS LIST / ASSEMBLY DIAGRAM PART # DESCRIPTION QTY Pressure Adjustment Knob Sinistral Screw Sinistral Nut Pressure Adjustment Mounting Spring Body Air Distributor Filter Mesh Filter Mesh Mounting “O” Ring Drain Cup Adjustment Screw Gasket Water Valve Drain Filter Valve Screw Brass Gasket Rubber Cover Rubber Screw Spring Rubber Gasket Pressure Gauge Mounting Bracket Retainer Ring 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS M...