Votes - , Average rating: ( )

User manual Everpure, model Kenmore 625.348241

Manafacture: Everpure
File size: 1.17 mb
File name:

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

STEPS TO ADD MINERAL 1. Press the face plate BACKWASH NOW button [] and hold for 3 seconds, until RCHG begins to flash in the display. 2. When water begins to flow from the valve drain hose, place the bypass valve(s) in BYPASS position.., see FIG. 8, page 18. CAUTION: BE SURE TO DO STEPS 1AND2 AS INSTRUCTED, TO RELIEVE WATER PRESSURE IN THE TANK. 3. Unplug the transformer at the wall outlet. 4. Carefully, pull the 2 clips (key #41, page 26) at the inlet and outlet fittings. Slide the adaptors, or bypass valve, from the filter valve. 5. Referring to FIG. 7, remove the clamp retainers (2) and clamp sections (2) that hold the valve to the tank. Lift upward to remove the valve. MEASURING FREEBOARD, ADDING MINERAL _-----_,_... bottom distributor _' funnel _ shroud / resin tank * "' rn l[ " , mineral bed mineral 3/4 used ...-sand _:_;_i_3! ..... gravel 14 SECTION 3 CARE OF YOUR FILTER I I 3B. ADDING MINERAL... NEUTRALIZER FILTER 6. Remove the o-rings (3) and top distributor from the top of the tank. 7. To make room for the new mineral, use a hose to siphon water from the tank. 8. Using a large neck funnel, add new mineral into the tank. IMPORTANT: DO NOT ADD MINERAL INTO THE Bo'n'OM DISTRIBUTOR. Temporarily plug the distributor tube to prevent accidental mineral spills into it. DO NOT OVERFILL the tank. Freeboard area (see FIG. 6) is needed for proper backwashing. If you have mineral remaining, you can use it the next time you refill the tank. 9. Use water to flush the tank top opening. Then, replace the top distributor and 3 o-rings. Be sure to locate o-ring seals correctly... FIG. 7. 10. Carefully, install the valve assembly and retaining clamps. DOUBLE-CHECK TO BE SURE CLAMPS AND RETAINERS ARE SECURELY FASTENED IN PLACE. 11. Referring to your installation manual, reconnect the filter tothe plumbing. BE SURE THE PLUMBING IS HELD FIRMLY IN PLACE, IN THE VALVE INLET AND OUTLET. 12. Place the valve drain hose at the drain point and secure in place. 13. Return the plumbing bypass valve(s) to SERVICE position. 14. Plug the transformer into the wall outlet. The filter will complete the backwash cycle, started in step 1, and will automatically return to service. 15 SECTION 3 CAREOFYOURFILTER [ I 3C. REPLACING MINERAL... TASTE & ODOR FILTER Average life of the activated carbon mineral bed is about 1 year (see page 12). It's time to replace the bed when the tastes and/or odors begin to return in the water supply. Do the following. STEPS TO REPLACE MINERAL = Press the face plate BACKWASH NOW button [] and hold for 3 seconds, until RCHG begins to flash in the display. = When water begins to flow from the valve drain hose, place the bypass valve(s) in BYPASS position.., see FIG. 8, page 18. CAUTION: BE SURE TO DO STEPS 1AND2AS INSTRUCTED, TO RELIEVE WATER PRESSURE IN THE TANK. = Unplug the transformer at the wall outlet. 4. Carefully, pull the 2 clips (key #41, page 26) at the inlet and outlet fittings. Slide the adaptors, or bypass valve, from the filter valve. = Referring to FIG. 7, page 14, remove the clamp retainers (2) and clamp sections (2) that hold the valve to the tank. Lift upward to remove the valve. g Remove the o-rings (3) and top distributor from the top of the tank. = Next to a floor drain, carefully tip the tank over, catching the used carbon in a burlap sack or other suitable container. Remove the bottom distributor assembly, and flush the inside of the tank with water. CAUTION: HANDLE THE TANK CAREFULLY. FULL OF WATER AND CARBON, IT IS VERY HEAVY. DO NOT ATTEMPT TO LIFT IT BY YOURSELF. DO NOT DROP AND BREAK THE TANK. . Stand the tank upright and replace the bottom distributor assembly....