Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Heater produces a clicking/ticking noise 1. Metal expanding while heating or con1. This is common w

CONTINUE GENERAL INSTALLATION 4. Connect both 1/2. NPT water lines (FIG 2) hot water outlet female and cold water inlet female and 3/8. flared LP gas line to the water heater (FIG 9). a. Allow flexibility in water and gas lines so you can pull unit forward through wall one inch past skin. b. Seal gas line entrance opening (FIG 9) by sliding grommet (9-B) onto 3/8. tubing (9-D) before flaring tubing (9-E). Pull gas line and grommet through opening in housing (9-A). Connect flare fitting (9-C) and

*Available from: American National Standards Institute, Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc. Batterymarch Park Quincy, MA 02269 Note:Do not remove Control Knob Lighting and Warning UNPACKING WARNING: Do not remove the metal data plates attached to the heater assembly. The data plates contain important warranty information. 1. Remove heater from carton. 2. Remove all protective packaging applied to heater for shipment. 3. Make sure your heater includes

Any alteration, like the addition of an aftermarket heating element device, will void the warranty. GENERAL INFORMATION • LP and Water system must be turned on. • Have gas pressure tested periodically. Should be set at 11 inches of water column with three appliances running. • Drain water heater at regular intervals (at least one time during the year). • Drain water heater before storing RV for the winter or when the possibility of freezing exists. • Keep vent and combustion air grill clear of a

The expansion tank must have a minimum capacity of 5.6 litres (1.5 US gallons) for every 190 litres (50 US gallons) of stored water and be rated at the working pressure of the water heater. Contact the local water supplier or plumbing inspector for information on other methods to control this situation. Important: Do not plug or remove the temperature and pressure relief valve. Temperature and Pressure (T&P) Relief Valve For protection against excessive pressures and temperatures, a temperature

Refer to page 3 of this manual. This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by state or local codes. * Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. Save this manual for future reference. BLUE FLAME 6000 BTU/HR VENT FREE PROPANE/LP GAS HEATER SAFETY INFORMATION WAR

The function of the temperature and pressure relief valve is to discharge water in quantities should circumstances demand. If the discharge pipe is not directed to drain as shown in Figure 2A, or other suitable means, the water flow may cause property damage. The discharge line: 1. must not be smaller than the outlet pipe size of the relief valve, 2. must not be plugged or blocked, 3. must be material capable of withstanding 99°C (210°F) without distortion, 4. must be installed so as to allow co

ROBERTSHAW 110R GAS CONTROL TEMPERATURE DIAL GAS CONTROL KNOB IN “PILOT” POSITIONPILOT BUTTON PILOT ELECTRODE THERMOCOUPLE IGNITER TO TURN OFF GAS TO APPLIANCE 1. Set the thermostat to lowest setting. Turn counterclockwise. 2.Turn the gas control knob “OFF”. Rotate clockwise. – 15 – Lighting Instructions (Robertshaw 220R) FOR YOUR SAFETY READ BEFORE OPERATING A. This appliance has a pilot which must be lighted by anigniter. When lighting a pilot, follow these instructionsexactly. B. BEFORE OPERA

FOR 6 ELEMENTS CONFIGURATION. ONLY C1, C2 WITH CORRESPONDING WIRING APPLIES. FOR 9 ELEMENTS CONFIGURATION. CIRCUIT IS AS SHOWN. 3A FUSE GND RED RED RED RED RED BLACK BLACK C2 (IF APPLICABLE) C1 L1 L2 L3 X1 X2 2 4 3 1 1 2 4 BLACK 3A FUSE OPTIONAL CONTROL TRANSFORMER (USED ON 480 OR 600V ONLY) HIGH-LIMIT THERMOSTAT 480 OR 600V CONTACTORS PRIMARY SECONDARY RED BLACK N 240V THERMOSTAT C3 (IF APPLICABLE) FOR 3 ELEMENTS CONFIGURATION. ONLY C1 WITH CORRESPONDING WIRING APPLIES. FOR 6 ELEMENTS CONFIGURA

Make sure material is secure. CAUTION: Do not pick up heater base assembly by burners. This could damage heater. Only handle base assembly by grates. IMPORTANT:Make sure the heater burners are level. If heater is not level, heater will not work properly. For thermostat models, avoid damage to thermostat bulb. Avoid nicks or sharp bends in thermostat bulb wire. Keep thermostat bulb in mounting bracket. Installation Items Needed • hardware package (provided with heater) • approved flexible gas hos