Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 25   File size: 314 kb   Manafacture: Chamberlain  
Category: Security Systems
@name

OPTIONAL AC Adapter Input A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release Learn Button on Base Station. Buzzer will sound. B Within 60 seconds, press the Learn Button on the inside of the PIR Motion Sensor. LED light will illuminate and Base Station will buzz. Learn Button 1 2 PIR Motion Sensor SWITCH #1: SWITCH #2: 3 4 Learn Button Insert battery pack facing away from circuit board and fasten cover with the smallest screws (provided). NOTE: En

downloaded: 0   File size: 1 mb   Manafacture: Chamberlain  
Category: Security Systems
@name

Accessories ______________________________________________________________________ 23 3. Primary Voltage Circuit ____________________________________________________________ 23 4. Low Voltage Circuit _______________________________________________________________ 24 General Reference Information_________________________________________________________ 25 Doc 01-G0674 Rev E Contents Required Maintenance-Normal Usage_____________________________26_Toc509797299 BG770 Drawing and Parts List_________

downloaded: 3   File size: 259 kb   Manafacture: Chamberlain  
Category: Security Systems
@name@name@name

• Automatically turns lighting off. • Dual Brite™ Timer. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Plastic Hanger Rubber Plug 6 MountingCover Screws (3 sizes) 3 Wire Connectors Mounting Bolt Light Control Mounting Strap Gasket 2 Halogen Bulbs Light Shield Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require

downloaded: 1   File size: 951 kb   Manafacture: Chamberlain  
Category: Security Systems
@name

Tighten screw until PIR Motion Sensor stays in place when repositioned. Base Station Passive Infra-Red (PIR) Motion Sensor Swivel Bushing Mounting Plate AC Adapter Rubber Pads Sun/Rain Shield Operation & Features Relay Output Contacts AC Adapter Base Station Switch #1 Base Station Switch #2 Learn Button Antenna Mute/Off Button Base Station Base Station Switches: Switch #1: Switch #2: Programming Additional PIR Motion Sensors: The Base Station can learn the code of up to 3 additional PIR Motion S

downloaded: 2   File size: 578 kb   Manafacture: Chamberlain  
Category: Security Systems
@name@name

• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). • Additional energy savings with compact fluorescent bulbs. This package includes: Lamp Holders Rubber Plug Plastic Hanger SensorCover Plate Light Control 2 Wire Connectors (3 sizes included) Mounting Bolt Mounting Strap Gasket 2 Compact 6 Screws Fluorescent Bulbs Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, t

downloaded: 0   File size: 2 mb   Manafacture: Chamberlain  
Category: Security Systems
@name

¦ The door WILL NOT CLOSE unless The Protector System® and cable tension monitor are connected and properly aligned. ¦ Periodic checks of the operator are required to ensure safe operation. ¦ The model number label is located behind the hinged door of your operator. ¦ Do NOT exceed 10 complete cycles of door operation per hour. 2 YEAR WARRANTY Serial # Installation Date TABLE OF CONTENTS Introduction 2-5 Safety symbol review and signal word review . . . . . . . . . . 2 Planning . . . . . . . . .

downloaded: 1   File size: 1 mb   Manafacture: Chamberlain  
Category: Security Systems
@name@name

Mute: To temporarily mute Base Station, hold the Volume and Talk buttons down for three seconds. The Base Station will reactivate after one hour, or by pressing the Talk button. Remote Button: If there is an accessory device connected to the relay on the PIR Motion Sensor, it can be activated by pressing the Remote button within 30 seconds of the signal from the alert buzzer. On/Off: To turn Base Station OFF hold down the Volume button until a beep is heard and light goes out. To turn Base Stati

downloaded: 0   File size: 128 kb   Manafacture: Chamberlain  
Category: Security Systems
@name

The Master PIN Number cannot be deleted. Erasing PIN Numbers “BEEP” “BEEP” “BEEP” ?? 51?? ?? 2 Mount Keypad Step 1 Choose mounting location for Keypad. Remove the back panel and attach it to a solid surface or post. Mount the Keypad onto the back panel with screws. Tighten screws with Allen wrench. Step 2 It is recommended that Keypad be mounted to a Gooseneck post or non-metallic surface. If it is necessary to mount Keypad to a metal surface, use a non-metallic spacer to move the Keypad away fr

downloaded: 0   File size: 165 kb   Manafacture: Chamberlain  
Category: Security Systems
@name

This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage. This feature can be easily turned off for extended work light use. Locate the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. NOTE: After installation, an indicator light behind the cover will indicate proper connection. If not lit, the Lock and

downloaded: 0   File size: 763 kb   Manafacture: Chamberlain  
Category: Security Systems
@name

The Passive Infra-Red sensor detects movement of people and vehicles, while allowing small animals to pass through undetected. The PIR Motion Sensor has a built-in microphone and speaker that allows for communication between the Base Station and the Sensor. When the PIR Motion Sensor detects movement a signal is sent to the base station which alerts the homeowner with sounds and lights. The Alert can also remotely control a low voltage electrical device near the PIR Motion Sensor like a light or





Category