Votes - 2, Average rating: 5
(
)
)
|
manual abstract
English 1. Important notice Unit parts Please fold out illustration page at the front 1 Handgun (with built-in pressure gauge) 2 Lever 3 Safety switch 4 Spray lance 5 High-pressure hose 6 Handgun support 7 Nozzle rest 8 Detergent metering valve 9 Cap for detergent reservoir 10 Detergent reservoir 11 Detergent suction-hose with filter 12 Fastening screws for unit cover 13 Pressure/flow control 14 High-pressure outlet 15 Water outlet with strainer 16 Checkpoint for oil level 17 Unit switch 18 Hose rest 19 Fastening screws for handle 20 Cable/hose rest 21 Handle 22 Nozzle For your safety Before you use the cleaner for the first time, read these operating instructions and take special note of the accompanying booklet “Safety Instructions for High-pressure Cleaners” No. 5.951-949. Use of the cleaner Use this cleaner exclusively for – cleaning with high-pressure jet and detergent (e.g. cleaning of machines, vehicles, buildings, tools) – cleaning with high-pressure jet without detergent (e.g. cleaning facades, terraces, gardening equipment). For stubborn dirt we recommend the dirt blaster as an optional accessory. Safety features Relief valve with pressure switch On reducing the flow rate with the pressure and flow control, the relief valve opens and part of the water runs back to the suction side of the pump. If the lever (2) is released, the pressure switch switches the pump off. If the lever is retracted, the pressure switch switches the pump on again. Warranty The warranty terms issued by our authorised marketing company are valid in every country. We remedy any fault in the cleaner free of charge within the warranty period providing the cause of the fault proves to be a material or manufacturing error. The warranty only becomes operative when your dealer has completed the reply card accompanying the sale of the unit, has stamped and signed it and you have then sent the reply card to the marketing company in your country. Should you wish to call upon the guarantee, please apply to your dealer or nearest authorised Customer Service centre taking along also the accessories and bill of sale. English 2. Preparing the cleaner for use Unpack the cleaner • When unpacking the cleaner, check the contents of the packaging. If there has been any damage in transit inform the dealer. • Do not dispose of the packaging with the household rubbish, hand it in at the appropriate collection point for recycling. Check the oil level See illustrations 1 to 3 at the end of the instructions. • Screw out the fastening screws on the left and right of the unit cover, remove unit cover. • Cut off the tip on the cover to the oil reservoir. • Check the oil level in the oil reservoir. • Fasten the unit cover. Mount the accessories See illustrations 4 to 6 at the end of the instructions. • Mount handle (screws and nuts supplied). • Engage the holder for handgun at the side of the handle. • Mount nozzle on the spray lance (see markings on the top of the setting ring). • Mount spray lance on the handgun. 3. Using the cleaner for the first time Electrical connection Caution!The voltage specified on the model rating plate must correspond to the voltage supplied. Caution!Use an extension cable whose cable cross-section is adequate (10 m = 2.5 mm., 30 m = 4 mm.) and unreel it completely from the cable drum. • For connected loads see model rating plate/ Technical Specifications Water connection/suction feed operation Connection to water main Caution!Pay attention to the regulations of the water supply company; according to DIN 1988, the cleaner may not be connected direct to the public drinking water supply. A short-term connection via a non-return valve (Order no. 6.412-578) is allowed. For connected loads see Technical Specifications. • Connect a supply hose (not supplied) to the water outlet (15) on the cleaner and to the water inlet (e.g. water tap). • Open water inlet. Suctioning water from an open container • Screw suction hose with filter (Order no. 4.440-238) to the water outlet (15). Venting the unit • To vent the unit, unscrew the nozzle and leave the unit running until the water exits with no air bubbles. • Switch off the unit and screw the nozzle back on. English 4. Operating the cleaner Danger!Observe the relative safety regulations when using the cleaner at filling stations or other high-risk areas. Caution!Only clean engines in places which have appropriate oil separators (protection of the environment). Caution!Only wash animals with the low- pressure fan jet (see “Selecting the type of spray”). Operating with high pressure The cleaner is equipped with a pressure switch. The motor only starts up when the lever (2) is retracted. • Press safety switch (3) and retract lever (2). • Set unit switch (17) to “I”. • Adjust operating pressure and flow rate (+/–) by rotating the pressure/flow control (13) (infinitely variable). Read off operating pressure on pressure gauge. Selecting the type of spray The handgun must be closed. • Rotate the ...