Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
SETUP
1. CAMERA SETUP MENU
This camera utilizes a user setup menu that is displayed on-screen.
• Opening the Setup Menu
Press and hold down
for 2 seconds or
Highlighted
more.
** CAM SET UP **
↵
CAMERA ID OFF
↵
ALC/ELC ALC
The CAM SET UP menu appears on the
SHUTTER OFF
AGC ON
monitor as shown at right.
SENS UP OFF
Check the current settings on the menu.
WHITE BAL ATW
↵
AUDIO LEVEL ....I....
- +
END SET UP DISABLE
Refer to the sections below for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END at the start
of the bottom line, and press
to close the CAM SET UP menu and return to normal cam-
era picture mode.
Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu
is opened, the menu is automatically closed and the mode returns to the normal cam-
era picture.
2. SETUP OPERATION
This camera utilizes a user setup menu
(CAM SET UP) that is displayed on the
Up
monitor.
Button
To set items on the CAM SET UP menu, use
the following buttons on the side panel.
Left Button
Right
Button
Set Button
Down
Button
Up Button (
):
Moves the cursor
upwards. Use this button to select an item or adjust the parameters.
Down Button (
): Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Right Button (
): Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Left Button (
):
Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Set Button (
):
Executes selections and displays a submenu for an item with ↵ mark.
END: Close Setup menu.
RET: Return to the previous menu.
To return to the CAM SET UP menu
Move the cursor to RET and press
. The CAM SET UP menu appears.
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both
and
, press
for a few seconds. The message ALL
RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When the SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you
cannot change the currently active settings. This is to prevent accidental changing of
the settings.
To edit the CAM SET UP menu (change
settings),
press and or and
** CAM SET UP **
** CAM SET UP **
CAMERA ID OFF
↵
CAMERA ID OFF
↵
to move the cursor to SET UP DIS-
ALC/ELC ALC
↵
ALC/ELC ALC
↵
SHUTTER OFF
SHUTTER OFF
ABLE in the bottom line.
AGC ON
AGC ON
SENS UP OFF
SENS UP OFF
Press
. SET UP DISABLE changes
WHITE BAL ATW
↵
WHITE BAL ATW
↵
to SET UP ENABLE. Move the cursor to
AUDIO LEVEL ....I....
AUDIO LEVEL ....I....
- +
- +
END, then to the item(s) you want to
END SET UP DISABLE
END SET UP ENABLE
change.
• Editing the SPECIAL Menu
To edit the SPECIAL menu (change set-
tings), proceed as for editing the CAM SET
** SPECIAL **
UP menu above. Move the cursor to END
UP SIDE DOWN OFF
after the SET UP ENABLE appears. Then
CHROMA GAIN ....I....
AP SHARP ....I....
press and simultaneously
(holding
PEDESTAL .I.......
down
and press
) for 2 seconds or
- +
more.
CAMERA RESET PUSH SW
The SPECIAL menu appears on the moni-
tor. Select the item to be changed and
RET END
change the setting as described for the
CAM SET UP menu.
Important Notice:
When the cursor is moved to END and the CAM SET UP menu closed after changing
the parameters, the new values are saved in the EEPROM (Electric Erasable and
Programmable Read Only Memory). These values remain valid until new values are
saved, even if the power of the camera is off.
(To be continued reverse page)
...