Votes - 1, Average rating: 5
(
)
)
|
manual abstract
2 Installation Caution and Warnings ............................................................................................... 3 Control Module and Components ............................................................................................. 3-4 Mounting Location………………………………………..................................................................4-5 Installations.................................................................................................................................. 6-7 LED Status Indicator........................................................................................................................ 8 Wiring…...................................................................................................................................... 9-10 Wiring Diagram………………........................................................................................................ 11 Access Information ...................................................................................................................... 12 2 INSTALLATION CAUTIONS & WARNINGS INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTERS, and BATTERY etc.). WE RECOMMEND the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated probes can cause damage to on-board computer or engine management systems. DO NOT exceed maximum output ratings or damage may occur. Electrical current limits for the TrakNet are listed where applicable on the system diagram. If you are unsure about the current load, of a specific circuit on your vehicle, measure the load first with an amp-meter before connecting. WE RECOMMEND that the MAIN SYSTEM FUSE be REMOVED before jump starting, using a battery charger, or changing the battery. A voltage surge or high boost condition could damage alarm circuits. DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column, or any other moving parts in the vehicle. CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine compartment or where the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The TrakNet control module and back up battery should be mounted in a concealed location. The antenna wire should be routed away from any metal if possible. Do not alter the length of the antenna wire or route it with other wires. Do not ground the antenna wire. Fasten the module to a bracket or wire harness using the cable ties. Under dash Mounting: If you are locating the control unit under dash, mount it as high as possible, not easily located. Antenna: The antenna location must be selected carefully so that the antenna can receive the satellite signals. The antenna is designed to be mounted inside the vehicle. The ideal location is in a place that allows line of sight reception from the GPS satellites. The antenna must be mounted flat with the GPS receiver facing up. The ideal location is under the dashboard. It can be placed under the dash pad as long as the covering is not metallic. The antenna works best if it has a clear view of the sky. Do not mount antenna under a window that has metallic tint on it. This will affect the reception of the unit. 3 CONTROL MODULE & COMPONENT MOUNTING CONTROL MODULE & COMPONENT MOUNTING Main Unit: The TrakNet unit has an internal power management program that monitors the vehicle power at all times. The internal power management program is continuously looking at the condition of the battery in order to detect the state of the vehicle operation. The Traknet unit determines the state of the vehicle power by detecting changes in the battery voltage over time. It is critical that the vehicle power be taken from a source as close to the battery as possible. Possible sources besides a direct connection to the battery is the main fuse block. Back Up Battery: Securely mount the battery so it wont move around. It can be mounted in various positions because the battery is sealed and should not leak. MOUNTING LOCATION Module Mounting Location The Traknet Unit is supplied with a 6 ft. power cable. The unit should be mounted so it will not be exposed to damage from people or objects. The cables that connect to the unit should also be routed to protect them from possible damage. The module has a mounting base or flange with four mounting holes. Normal installation is with these four holes and #6 or #8 sheet metal screws. The unit must be mounted where it will not be exposed to direct sunlight or excessive heat generated by the vehicle operation. Some examples of mounting locations include under the dash above the knee bolster, under center console, behind glove compartment, and in the trunk. If the optional battery is to be installed there should be room to mount the battery within 1 f...
Other models in this manual:Security Systems - TN-4003 (352.65 kb)