Votes - 2, Average rating: 3
(
)
)
|
manual abstract
19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn. Allied Telesyn International, Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesyn has been advised of, known, or should have known, the possibility of such damages. All trademarks are the property of their respective owners. Quick Install Guide AR450S Router AR450S Quick Install Guide AR Router Hardware Reference AR400 Series Software Reference General Customer Support Visit for the latest documentation, FAQ, and support information Documentation Roadmap AR400 Series User Guide AR400 Series Safety and Statutory Information Website Printed Acrobat PDF Models Covered By This Guide This Quick Install Guide includes information on the following model: ¦ AR450S Quick Install Guide updates can be found at Package Contents The following items are included with each AR450S router. Contact your sales representative if any items are damaged or missing. ¦ One AR450S router. ¦ One AC power cord. ¦ One power cord retaining clip. ¦ One terminal cable for connecting the router to a terminal or PC. ¦ Two UTP network cables. ¦ One rack-mount kit with brackets and screws. ¦ One AR450S Router Quick Install Guide. ¦ One Safety and Statutory Information booklet. ¦ One AR400 Series Router Documentation and Tools CD-ROM (which includes the complete AR400 Series Document Set and utilities). ¦ One warranty card. C613-04045-01 REV A AR450S Router Selecting a Site The router should be installed on a level surface such as a desktop or bench. When installing the router, choose a site that: ¦ Allows adequate airflow around the router and its vents. ¦ Is free of dust and moisture. ¦ Will maintain an ambient temperature range of 0 to 40. C (32 to 104. F) and a humidity range of 5 to 95% non-condensing. ¦ Has a reliable and earthed (grounded) power supply circuit, preferably dedicated and filtered. ¦ Does not expose cabling to sources of electrical noise, such as radios, transmitters, broadband amplifiers, power lines, electric motors, and fluorescent fixtures. ¦ Allows easy access to the router’s power and cable connections. Installing the Router This equipment must be earthed. Follow these steps to install the router: 1. Read the safety information. For safety information, see the Safety and Statutory Information booklet. A copy of this booklet is supplied with each router, and can also be found on the Documentation and Tools CD-ROM or at 2. Unpack the router. Verify the package contents. If any items are damaged or missing, contact your sales representative. 3. Place the router in its operating location. See the previous Selecting a Site section for guidelines on choosing a suitable location. 4. Check the supply voltage and the router’s rated voltage. AR450S routers are fitted with a universal mains power supply that will function over the range 100-240 VAC and 50–60Hz. The specific power supply requirements for a particular model are clearly displayed on the rear or underside of the router. If the supply is outside the accepted range for the router, the router may not operate and damage to the router may result. C613-04045-01 REV A Quick Install Guide 5 C613-04045-01 REV A 5. Apply power to the router. Fit the power cord retaining clip to the AC power inlet on the router’s rear panel. Connect the provided power cord to the AC power inlet and clip it in place. Switch the router’s power switch to the ON position. The Power LED will light continuously and the System LED will flash briefly. The Port LEDs may also light briefly. If the LEDs fail to light, the most likely cause is that the router is not receiving power. Check that • The power supply outlet’s switch (if any), and the router’s power switch, are in the ON position • The power cable is securely plugged in • The power supply is operational If the LEDs light incorrectly, refer to the AR Router Hardware Reference for troubleshooting information. Figure 1: Front and rear panels of an AR450S, showing the AC power inlet, power switch, console ports and Ethernet ports, and their associated LEDs. Configuring the Router AR450S routers can be configured via the Command Line Interface (CLI) or Graphical User Interface (GUI). Using the CLI to configure a router: 1. Initiate router start-up. Using the terminal cable supplied, connect a VT100-compatible terminal, or the COM port of a PC running a termin...