Votes - 3, Average rating: 4
(
)
)
|
Other manuals for this model:
Security Systems - VB-C50FSi (10.14 kb)
Security Systems - VB-C50FSi (21.91 kb)
manual abstract
Please note that the Multi-Terminal Module VB-EX50 is an optional product and is therefore sold separately. * Audio function is available with VB-C50FSi. * Besides, Audio input is only available with a Before Using the VB-C50FSi/VB-C50Fi particular model of the VB-C50FSi (> P.iii). Example of Use With the Multi-Terminal Module, you can perform settings such as the following. Sensor A VB-C50Fi Multi-Terminal Module VB-EX50 Ethernet Sensor B . The door open-close sensor responds when the door is opened and with the VB-C50Fi installed on the ceiling, you can photograph an image and monitor the scene every second for 3 seconds before the door opens and for 7 seconds after the door is opened (> P.6-2). Tip By using a speaker with amp and microphone* connected to the VB-C50FSi, the Viewer Administrator can converse with the person in front of the camera, hear and record* the sounds in the background (> P.3-18, 3-19) * Only available with a particular model of the VB-C50FSi (> P.iii) 1-11 2 Setting Up This chapter explains how to set up the VB-C50FSi/VB-C50Fi, run initial checks, and confirm that the camera’s images are displayed correctly. 2-2 1 Set up the camera 3 Per form ini t ial set t ings for the camera 2 Connect the camera to the network LAN cable VB-C50FSi Hub Set up the device. Make sure the device is set up properly (> P.2-4). Connect the camera and your PC via the hub (> P.2-6). Insert the CD-ROM provided into your PC and perform initial settings following instructions on the screen (> P.2-8). Supplied CD-ROM Setup Workflow The flow for setting up and checking the camera’s images involves performing various settings after the device is set up and your PC and the network are connected via the hub. Then, check to see if you can display images from the camera. Install the software5 Install the required software in advance for operating the camera (> P.2-13). Setting Up Check operation of the camera4 Access the device with your PC, then display to check the image from the top page of the camera server (> P.2-11). 2-3 Set Up the Camera Firstly, set up the camera. Read the following carefully and make sure the camera is set up properly. Mounting the Camera to the Ceiling or Wall When Using a Tripod Attach a mounting arm (not included) to the ceiling or a wall and firmly attach the camera to the arm. Less than30 mm 6.0 mm (1.18 in.) (0.24 in.)or wider Mounting screw a WARNING: Install the camera securely. .When installing the VB-C50FSi/VB-C50Fi on the ceiling or a wall, contact your Canon dealer. .When installing the VB-C50FSi/VB-C50Fi on the ceiling or a wall, check that it is strong enough to bear the weight of the VB-C50FSi/VB-C50Fi including the mounting arm. Installation in a weak location could result in the VB-C50FSi/VB-C50Fi falling and causing serious injury. Check that the ceiling can hold either 3 times the weight of the camera and arm or 8kgs (whichever is heavier) for 1 minute. .When attaching the arm to the ceiling, make sure that the screws are tightly fastened. The arm and camera may fall if the screws are not tightly fastened, which may cause serious injury. .At least once a year, check for looseness in the camera installation mount. (If the optional wide converter is used, check the converter mount also). .Do not install the arm in a place that shakes or vibrates frequently as the screws may come loose causing the camera to fall or be damaged, which in turn may cause serious injury. Note .The MAC address required when making network settings is shown on the rear of the VB-C50FSi/VB-C50Fi (> P.1-10). Please make a note of it before installing this unit. .Always use a tripod mounting screw that is less than 6.0 mm (0.24 in.) in length. The use of screws 6.0 mm (0.24 in.) long or longer could damage the camera. Also, the tripod seat used should be at least 30 mm (1.18 in.) in diameter. Set Up the Camera Using the Wide Converter The optional Wide Converter WL-37 can be used to provide wide-angle shots (approx. 0.74. the normal focal distance). Mount the wide converter correctly so that it is level and fitted securely onto the camera. When mounted correctly, the wide converter should turn roughly 3 times before stopping. Wide Converter Note .The camera may not operate correctly if a wide converter other than the WL-37 is used. .Be sure to install the VB-C50FSi/VB-C50Fi firmly because the weight of the camera increases when the optional Wide Converter WL-37 is attached. .If you use the optional Wide Converter WL-37, set the zoom lens to the wide-angle end. If you set the zoom lens to the telephoto end, the image resolution will be affected and the auto focus might have problems. 000000Setup is now complete. Setting Up 2-5 2-6 2. Connect the Camera to the Network Next, connect the camera. Connect the camera to the network by connecting the camera and PC via the hub with a LAN cable . * Do not plug the AC cable power plug into the wall socket yet. PC Hub LAN cable AC cable AC adapter (Rear of main u...
Other models in this manual:Security Systems - VB-C50Fi (9.52 mb)