Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Synchronization Setting (SYNC) 1. Select a sync mode. VD2: Multiplexed vertical drive, highest priority LL: Line-Lock, follows the phase of supplied AC power, 2nd priority INT: Internal sync, lowest priority Notes: • Selection is not available when VD2 is added to the camera. Selection from LL is available when the respective sync is added. • When LL is selected, phase adjustment is required. 2. Line-Lock Vertical Phase Adjustment (V PHASE) • Select LL and press the [SET] button. • Prepare a dual-trace oscilloscope and supply it with the video output of the camera to be adjusted and that of the reference camera. • Set the oscilloscope to the vertical rate and expand the V-sync portion. • Select a proper COARSE phase from 16 steps (22.5 degrees/step) that makes the two video signals on the oscilloscope the closest. • Select a proper FINE phase so that the two video signals on the oscilloscope come as close as possible. Notes: • Moving the "I" cursor across the +/- end will shift the FINE range. • Press the [LEFT] and [RIGHT] buttons simultaneously to reset the V PHASE to the default (0 degree). • Keep pressing the [LEFT] and [RIGHT] buttons for a second to move the "I" cursor faster if necessary. • Spike noise if contained in the AC mains may disturb synchronization of LL. 7. White Balance Setting (WHITE BAL) Select a mode for WHITE BAL on the CAMERA SETUP menu. The default setting is ATW1. ATW1: Is automatically adaptable to the color temperatures of 2 700 K - 6 000 K. ATW2: Is automatically adaptable to the use of sodium lamps (2 000 K - 6 000 K). AWC: Is automatically adaptable to the color temperatures of 2 000 K - 10 000 K. Notes: • When ATW1 or ATW2 is selected, no further operation is required. • ATW1 and ATW2 do not appear on the setup menu of the system controller. • Select AWC in the following cases: the color temperature is out of the 2 000 K - 6 000 K range, the scene contains mostly high color temperatures such as blue sky or sunset, or the scene is dim. • When AWC is selected, the AWC setting is required. AWC Setting 1. Select AWC and press the [LEFT] button. > AWC will change to AWC > PUSH SW. 2. Press the [SET] button. > PUSH SW will be highlighted while the AWC setting is performed. Note: If the white balance is not set, PUSH SW is being highlighted. 3 . Press the [RIGHT] button. Manual Fine Adjustment **ATW1** Perform fine adjustment as necessary. 1. Select WHITE BAL and press the [SET] but-R ...I...128 -+ ton. B ...I...128 > Fine adjustment menu of ATW or AWC will -+ open. 2. Adjust finely R (Red) and B (Blue) gain by moving the "I" cursor. RET TOP END 8. Motion Detection Setting (MOTION DET) When a series of changes in pictures is detected, the camera outputs an alarm to the external device such as a disk recorder. The recorder will start recording the pictures. 1. Select a mode for MOTION DET on the CAMERA SETUP menu. The default setting is OFF. OFF: Disables the alarm output. MODE1: Outputs alarm when a series of motions is detected. MODE2: Outputs alarm when a series of scene changes is detected. ** MODE1 ** LEVEL ...I..128 -+ DWELL TIME 2S DISPLAY MODE ALARM OFF MASK SET RET TOP END . . > The MODE1 menu opens when you select MODE1 and press the [SET] button. 2. Adjust for LEVEL to optimize the sensitivity of detection. 3. Select a dwell time. The default setting is 2S. Available time (second): 2, 5, 10, 30 The next detection will be performed after the set time elapses. 4. Select MASK SET and press the [SET] button. > A 48-split screen opens. • Specify non-detection (mask) and detection areas in the same way as described earlier in 2-2 ALC Mode. • Hold down the [SET] button for 2 seconds to return to the MODE1 menu. Note: Perform the setting of mask area after STABILIZER in the CAMERA SETUP menu is set to OFF. 5. Select ON or OFF for ALARM under DISPLAY MODE. ON: Outputs an alarm OFF: Does not output an alarm. This is applicable any of the following controllers are used: WV-RM70, WV-CU550 series, WV-CU161, WV-CU360, WV-CU650, WV-CU850, WVCU950 6. Select DISPLAY MODE and press the [SET] button to see the current settings. When a motion is detected, the area will blink. • Press the [SET] button to return to the MODE1 menu. 7. As necessary, repeat to perform LEVEL adjustment and MASK setting by checking on the DISPLAY MODE screen. Notes: • In systems other than Panasonic, select OFF for MOTION DET to prevent system devices from confusing time-code signal with alarm signal. • Set MASK SET over the areas where leaves or curtains etc. are swaying. • Adjust the detection level to prevent detection from confusing motion with noise under low light conditions. • It takes around 0.2 seconds for the alarm signal to reach the VCR’s alarm terminal after detection. • The motion/scene change detection is not specifically intended to prevent theft or fire. Motion Detector The motion detector divides the screen into 48 blocks and monitors changes in the luminance in each block. When it detects any chan...