Votes - 3, Average rating: 4
(
)
)
|
manual abstract
UP: Upward DOWN: Downward L: Left R: Right i Iris buttons (IRIS CLOSE/OPEN) Close or open the lens iris of cameras equipped with the specified lens. When these buttons are pressed at the same time, the lens iris is reset to the factory setting. o Focus buttons (FOCUS NEAR/FAR) Adjust the lens focus of cameras equipped with the specified lens. When these buttons are pressed at the same time, the lens focus is set automatically when the specified camera, such as the WV-CS854, is used. !0 Zoom buttons (ZOOM TELE/WIDE) Zoom the image in or out if the camera is equipped with the specified lens. !1 Auxiliary button (AUX) In combination with the number buttons 1 to 4, controls the Auxiliary switches for the Receiver, Wiper and Defroster. Press the numeric button, then press this button to turn the Auxiliary switches for the Wiper or Defroster On or Off. 1: Auxiliary Switch 1 2: Auxiliary Switch 2 3: Wiper 4: Defroster !2 Panning button (PAN) In combination with the numeric button 1 or 2, is used to control the panning mode of the Pan/Tilt Head. Press the numeric button, then press this button to turn the Panning mode On and Off. 1: Auto Panning Mode 2: Random Panning Mode !3 Preset Position button (PRESET POSI/CAM POSI) In combination with the numeric buttons, moves the camera to the desired preset position. Also selects a camera position by a serial number assigned independently of the camera number. Specify a number, then press ALT and finally this button. !4 Camera/Set button (CAM (SET)) CAM: Used for camera selection. To select a camera, enter the desired camera number with the numeric buttons, and then press this button. SET: Executes the currently highlighted setting in the setup menu of the Matrix Switcher and opens a submenu. !5 Numeric buttons (0 - 9) These buttons are used for numerical input such as camera and monitor selection, sequence and preset position, etc. Buttons 2, 4, 6 and 8 are also used to move the cursor to the desired position on the Camera’s Set Up Menu. !6 Monitor/Escape button (MON (ESC)) MON: Used for monitor selection. To select a monitor, enter the monitor number with the numeric buttons, and then press this button. ESC: Escapes from or executes the currently highlighted selection in the setup menu of the matrix switcher. !7 Alternate button (ALT) Alternates the function of dual-function buttons between the normal and the alternate function. It also enables the CAM MENU button and SET UP button to display the assigned menu or setup table on the selected monitor. The indicator is lit while the function mode is selected. !8 Sequence Pause button (PAUSE) Pauses a sequence that is being run on the selected monitor. !9 Function button (FUNCTION) Pressing this button in combination with another operation button activates a specific function. @0 Alarm Acknowledgment and Reset button (ACK/RESET) Cancels an activated alarm. To cancel the alarm, the monitor must first be selected. Press this button once to acknowledge the activated alarm (the indicator blinks rapidly), then press it again to reset the alarm. @1 @2 Backward/Forward Sequence button @9 Status button (STATUS) (SEQ BACK/FWD) Toggles the display of the Camera Site Status Table on BACK: In combination with the numeric buttons, runs a the selected monitor On and Off. Tour or Group sequence backward on the selected Note: To toggle the display of the System Status Table monitor. on the selected monitor On and Off, press this but- It is also used to continue a sequence backward, ton in combination with the ALT button. that was previously paused on that monitor by pressing the PAUSE button. #0 Camera Menu button (CAM MENU) FWD: In combination with the numeric buttons, runs a In combination with the ALT button, toggles the display Tour or Group sequence forward on the selected of the selected Camera’s Setup Menu On and Off. monitor. The indicator lights up when the camera setup mode is It is also used to continue a sequence forward, that selected. was previously paused on that monitor by pressing the PAUSE button. #1 Set Up button (SET UP) In combination with the ALT button, toggles the display @3 All Alarms Reset button (ALL RESET) of the SETUP MENU of the Matrix Switcher On and Off. Cancels all active alarms at a time. The indicator lights up when the setup mode is select- To reset all alarms, first select the alarmed monitor ed. (Monitor 1 for Alarm Mode 1, any of four monitors for Alarm Mode 2), and then press this button. Note: To cancel all alarms without first selecting the monitor, press this button in combination with the ALT button. @4 @5 Decrement/Increment button (–1CAM DEC, +1CAM INC) –1CAM DEC: Moves a sequence one step backward from the step that was previously paused on the selected monitor by pressing the PAUSE button. Also, when the selected monitor is in the spot mode, pressing this button will replace the currently selected camera with the next lower number camera. +1CAM INC: Moves a sequence one step forward from the s...