Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
The default setting is "24" (referring to the NTP server every 24 hours). TIME ZONE Set the time zone (GMT) of where the encoder is installed. The default setting is "(GMT - 05:00) Eastern Standard Time". DAYLIGHT SAVINGS Select "ON" or "OFF" to set whether to apply the summer time according to the area selected for "TIME ZONE". When "ON" is selected, the clock is automatically advanced one hour in summer and is put back one hour in winter. The default setting is "ON". DATE It is possible to set the time and date manually. This setting is valid when "OFF" is selected for "NTP". The displayed time and date is the time and date when this page is opened. Enter time and date in the respective input boxes. The valid time and date ranges are as follows. [YYYY/MM/DD] 2003/01/01 - 2038/01/19 [hh:mm:ss] 00:00:00 - 23:59:59 The default settings are "2003/01/01" and "00:00:00" respectively. Note: If these settings are performed, it is possible to be informed of the time and date of an alarm occurrence. When "MAIN CPU MODE (MAIN CPU EXISTS)" is selected for "MODE", it is possible to select whether the time and date to be displayed on the monitor are the time and date set on the camera side or on the control side. ¦ DEVICE NAME/LOCATION/CONTACT/ SNMP COMMUNITY Perform these settings only when using the SNMP (Simple Network Management Protocol). Enter alphanumeric characters or punctuation marks except for the double quotation mark (") and the semicolon (;). ¦ MAIN CPU MODE SETUP When "MAIN CPU MODE (MAIN CPU EXISTS)" is selected for "MODE", it is necessary to set the items in this section. Note: The main CPU mode is the advanced function for integrated control. START UP COMMAND Depending on the network environment, select "BROADCAST", "MULTICAST" or UNICAST". When "MULTICAST" or "UNICAST" is selected, enter also the "DESTINATION IP ADDRESS". The entered IP address will be the destination IP address of the Main CPU receiving the start up command. The default setting is "239.192.255.1". MULTICAST IP ADDRESS FOR SETUP/MULTICAST PORT No. FOR SETUP Enter an IP address and a port number to receive the setup command from the Main CPU. The default settings are "239.192.255.2" for the IP address and "51203" for the port number. USER page Perform the settings to restrict users to access the encoder on this page. It is possible to restrict access to the encoder by the "USER AUTHENTICATION" and the "HOST AUTHENTICATION". Refer to the next page when using both the "USER AUTHENTICATION" and the "HOST AUTHENTICATION". Notes •The following user (administrator) is registered as default setting. USER NAME: admin PASSWORD: none (blank) ACCESS LEVEL: 1 (ADMINISTRATOR) • It is impossible to delete the user "admin". It is possible to set a password for the user "admin". However, if the entered password is forgotten, it is necessary to reset all the settings to the default settings by setting the "SW2" switch on the front panel of the encoder to "ON". When the password is entered, write it down and keep it safely so as not to forget it. • Click the [SET] button to save the changed settings. Otherwise, the changed settings will not be saved. ¦ Item Descriptions . USER AUTHENTICATION Select "ON" or "OFF" to set whether to apply the user authentication or not. However, when using a web browser to perform the settings, it is necessary to be authenticated regardless of the "ON" or "OFF" setting. The default setting is "OFF". . SETUP Up to 16 users can be registered. A registered user can be deleted using the "DELETE" pull-down menu in the section at the bottom of this page. USER NAME/PASSWORD Enter up to 16 alphanumeric characters for the user name and the password. However, the colon (:) and the semicolon (;) cannot be used. PASSWORD (TWICE) Enter the password again for confirmation. ACCESS LEVEL Select one of the following for the access level. 1 (ADMINISTRATOR) It is possible to perform the settings on the settings pages and operate the encoder using the CGI commands. 2 (CAMERA CONTROL) It is possible only to operate the encoder using the CGI commands. It is not possible to perform the settings on the settings pages. [ADD] button Click to add a user after entering the user information. . DELETE Select a user to be deleted from the pull-down menu, and click the [DELETE] button. In the pull-down menu, user names are displayed with their access level as follows. Example: admin[1] Confirm that the user has been deleted from the pull- down menu. Note: To set the password for the default user "admin", enter "admin" in the "USER NAME" input box, and the password in the "PASSWORD" and "PASSWORD (TWICE)" input boxes. The access level setting will be fixed to "1 (ADMINISTRATOR)". SETTINGS MENUS OF THE ENCODER HOST page Perform the settings on this page when restricting devices from accessing the encoder by using IP addresses. It is possible to restrict access to the encoder by the "USER AUTHENTICATION" and the "HOST AUTHENTICATION". Notes: • Click the [S...