Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Camera cable connector [CAMERA] (26-pin connector) The camera’s cable (such as the AW-CA50A26) is connected here. . Contact-type pan/tilt head control connector [PAN/TILT CONTROL IN] (D-SUB 15-pin connector) . This has the same shape as the tally/intercom input/ output connector. Take care not to confuse the two when connecting them. A controller for controlling the lens (a lens with zoom and focus servo) and pan/tilt head (up, down, left, right, defroster, wiper, etc.) is connected here. (Only a contact-type controller can be connected.) Pin No. Signal Name 1 LEFT 2 RIGHT 3 UP 4 DOWN 5 FAR 6 NEAR 7 TELE 8 WIDE 9 DEFROSTER 10 WIPER 11 COMM 12 +5 V 13 +V (+7.5 V) 14 –V (+2.5 V) 15 GND . The optional board must be installed in the camera in order to use a contact-type pan/tilt head. For details, refer to the camera’s operating instructions. . When the control pins (#1 to #10) are connected to the COMM pin (#11), the control signals are sent from the RCU to the camera. . When the controller is to be fabricated, connect a resistor with a resistance of 1 to 10 kilohms (1/8 W or more) between the COMM pin and +5 V pin. . Ensure that both the LEFT and RIGHT pins are not connected to the COMM pin at the same time. . Similarly, do not connect both the UP and DOWN, FAR and NEAR or WIDE and TELE pins to the COMM pin at the same time. . Pins #12 to #15 are used when exercising lens control only. To do this, connect the controller’s FOCUS CONT pin to NEAR (pin #6) and its ZOOM CONT pin to WIDE (pin #8). (Normally, pins #12 to #15 are not used when exercising control by contacts.) . Gen-lock input/output connector [G/L IN/OUT] (75-ohm automatic termination) The external sync signals (black burst signals or composite signals) from another system are connected here. Note: The input signals must be connected to the BNC connector marked “IN” (75-ohm automatic termination). If it is connected to the BNC connector marked “OUT,” a high-impedance state will result, and the connector will not be terminated by the 75-ohm resistance. . AUX signal input/output connector [AUX IN/OUT] (75-ohm automatic termination) Connect the line view signals from a live switcher or other device here. Note: The input signals must be connected to the BNC connector marked “IN” (75-ohm automatic termination). If it is connected to the BNC connector marked “OUT,” a high-impedance state will result, and the connector will not be terminated by the 75-ohm resistance. 11 Parts and their functions . Video output connectors [VIDEO1, VIDEO2] The video signals from the camera after cable compensation are output from these connectors. (The same signal is output from connectors 1 and 2.) Connect the connectors to the video input connectors on the live switcher, color monitor, VTR or other device. (Output impedance: 75 ohms) . SYNC output connector [SYNC] The composite sync signal is output from this connector. Connect the connector to the gen-lock input connector on the color monitor or other device. (Output impedance: 75 ohms) . RGB/Y, PR and PB/YC output connectors [R/PR/C, G/Y/Y, B/PB] If a camera such as the AW-E650 with RGB/Y, PR and PB/YC signal output facilities is connected to the remote control unit, its signals are output from these connectors. (Output impedance: 75 ohms) The RGB/Y, PR or PB/YC signals are selected using the camera’s menu. (For details, refer to the camera’s operating instructions.) . S-Video output connector [S-VIDEO OUT] (4-pin S-connector) The same signals as the ones output from the R/PR/C and G/Y/Y connectors among the RGB/Y, PR and PB/YC output connectors . are output from this connector. (Output impedance: 75 ohms) The YC signals are selected using the camera’s menu, and connected to a color monitor or other device equipped with an S-Video input connector. Note: When the RGB/Y, PR and PB/YC output connectors . and S-Video output connector . are used at the same time, the level of the output signals will be reduced. Therefore, use either connectors . or connector . in line with the connectors used on the device connected to the remote control unit. . Tally/intercom input/output connector [TALLY/INCOM] (D-SUB 15-pin connector) Connect this to the TALLY & INCOM connector on the live switcher (AW-SW350). Set the INCOM selector switch on the live switcher (AW-SW350) to [3-wire type]. When inputting the tally control signals from another device, input them with 0V for ON and open for OFF. Pin No. Signal Name 1 TALLY 6 INCOM MIC 7 INCOM GND 8 INCOM SP 11 TALLY GND . Fuse holder [FUSE] Fuse used: HT1.6AN5 (AC 250 V, 1.6 A) . AC power socket [AC IN] Attach one end of the power cord provided to this socket and the other end to the AC 120V (60 Hz) power supply. 12 Connections . Before proceeding with the connections, ensure that the power to all the devices is off. . Be absolutely sure to use the AW-CA50A26 RCU cable to connect the RCU to the camera. . When extending the cable, use the extension-use studio cable (WV-CA26U15, WV-CA26U30 or W...